Sharp SRT-8960 Other Specifications, Connectors When the Terminal SET is set to SET2

Page 54

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SPECIFICATIONS

Other Specifications

Operating temperature range	5°C to 40°C (41°F to 104°F)
Operating humidity range	80% or less
Power requirements	120V AC,60Hz
Power consumption	15 W
Dimensions (W x H x D)	420 mm x 99.5 mm x 306 mm (16.54″ x 3.92″ x 12.05″ )
Weight	approximately 4.0 kg

Connectors (When the “TERMINAL SET” is set to “SET2”)

NOTES:

œThe terminal names and signals are different from the usual setting.

œNames in brackets apply to terminals on the rear panel.

Clock set input (CONTROL IN)	No voltage, make-contact switch input (Low input 100ms or more,
	Normally 5 V)
Clock set output (CONTROL OUT)	DC 5 V, 5.7kΩ, (Low output)
Eject input (SERIES IN)	No voltage, make-contact switch input (Low input 100ms or more,
	Normally 5 V)
Eject output (TIMER OUT)	DC 5 V, 5.7kΩ, (Low output)

NOTE: The specifications and external appearance of this unit are subject to change without notice.

English

Image 54

Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireContents FeaturesAccessory Locations of Controls and Indicators Front PanelOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsMain Menu Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Sub-menusON-SCREEN Menu Setting the Language and Clock Language SettingClock setting Setting the Language and Clock Automatic Daylight Saving Time AdjustmentFactory setting Superimpose Display Selecting the Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape ManagementOperation If tape management data is present on the tapeSetting the Tape Management Function Tape ManagementTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording Speed ModeNormal Recording Before startingRecord Pause Pause/still indicator N flashesNormal Recording Recording CheckSetting the clog detection Action to Take when the Video Signal DeterioratesClog Detection Setting when not using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when using Autorepeat recordingRepeat indicator lights Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingALARM/SERIES REC SET menu appears Alarm Recording Counter Display Alarm RecordingAlarm Recording Reset Function Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Operation Series Recording SetupSeries Recording Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationDAY/TIME Search Tape CounterDay/Time Search Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Quick Method Security LockClock Adjustment Selecting Input and Output TerminalsConnection Eject output Timer OUT terminal Setting the Cassette Eject ModeCassette Eject Setup Eject input Series in terminalOperator Mode Synchronization ControlSynchronization Control Setting the Cassette Eject ModeAdministrator/Installer Mode SC will flash on the digital displaySetting for RS-485 or RS-232C USE Setting the Address and Data Transfer SpeedSettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Output Terminals Timer OUT terminalTape END OUT Terminal Output Setting Tape END OUT TerminalSW OUT Terminal Output Setting Output TerminalsSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Connectors SpecificationsGeneral Specifications VideoSpecifications Other SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time