Sharp SRT-8168, SRT-8960, SRT-8040 Synchronization Control, Setting the Cassette Eject Mode

Page 43

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SYNCHRONIZATION CONTROL

Setting the Cassette Eject Mode

Operator mode can be used to eject cassettes for all VCRs or for specified VCRs.

1Follow steps 1 to 4 under “Operator Mode”.

2Turn the JOG dial until the “EJECT MODE” setting is highlighted, then turn the SHUTTLE ring clockwise.

3Turn the JOG dial to select the desired cassette eject mode, then turn the SHUTTLE ring clockwise.

EJECT1 . . . . . . . . . . . . The cassette is ejected only if the VCR is not in recording or recording pause mode.

EJECT2 . . . . . . . . . . . . The cassette is ejected only if the VCR is in stop mode.

4Press the MENU EXIT button.

Administrator/Installer Mode

This mode lets you carry out basic operations (ejecting, recording, stopping, rewinding and changing the recording speed mode) and also make menu settings.

NOTES:

œThis mode will not work correctly unless the VCRs are in the same initial state.

œMenu settings will not work correctly unless the menu settings for the VCRs are the same. Set the menu settings for each VCR to the initial setting before using this mode to change the settings.

œIf a power failure occurs, make the settings again.

1While holding the STOP button, press the STILL/PAUSE button for 3 seconds or more on the VCR that is set to be the master VCR.

ø“SC” will flash on the digital display.

“SC” flashes (master) . The menu settings can be changed for the VCR being operated and all VCRs that are connected after it.

œThis mode can be used regardless of the “OPERATION” setting in the (WARNING OUT/CONTROL SET) menu.

“SC” off (slave) . . . . . . The menu settings can be changed for only the VCR being operated.

œTo cancel the master mode, press and hold the STOP button and then press the STILL/PAUSE button.

42

English

Image 43

Contents SRT-8960 SRT-8168 SRT-8040 For customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationFeatures ContentsAccessory Front Panel Locations of Controls and IndicatorsDigital Display Locations of Controls and IndicatorsOperation Indicators Operation Mode IndicatorWith the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface boardConnections Power Cord InstallationSub-menus Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Main MenuON-SCREEN Menu Language Setting Setting the Language and ClockClock setting Automatic Daylight Saving Time Adjustment Setting the Language and ClockFactory setting Selecting the Superimpose Display Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape ManagementOperation If no tape management data is present on the tapeTape Management Setting the Tape Management FunctionTape Management menu appears Conflict display sample Tape Management Conflict DisplayBefore starting Recording Speed ModeNormal Recording Normal RecordingRecording Check Pause/still indicator N flashesNormal Recording Record PauseAction to Take when the Video Signal Deteriorates Setting the clog detectionClog Detection Setting when using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when not using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording Alarm Recording Setting Alarm RecordingALARM/SERIES REC SET menu appears Connections to the Alarm in Terminal Alarm RecordingAlarm Recording Reset Function Alarm Recording Counter DisplayAlarm Scan Alarm SearchProgram Timer Recording Timer SET menu appears Program Timer RecordingTo cancel all program timer recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Recording Using AN External Timer Input Loop recording Series Recording SetupSeries Recording OperationSingle Image Recording Single Image Recording SetupNormal Playback Special Playback Shuttle Ring Operation Special PlaybackTape Counter DAY/TIME SearchDay/Time Search Quick Method Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Security LockSelecting Input and Output Terminals Clock AdjustmentConnection Eject input Series in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject output Timer OUT terminalSynchronization Control Operator ModeSC will flash on the digital display Setting the Cassette Eject ModeAdministrator/Installer Mode Synchronization ControlSetting the Address and Data Transfer Speed Setting for RS-485 or RS-232C USESettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Timer OUT terminalTape END OUT Terminal Output Setting Output TerminalsOutput Terminals SW OUT Terminal Output SettingSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control settingMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Video SpecificationsGeneral Specifications ConnectorsOther Specifications SpecificationsConnectors When the Terminal SET is set to SET2 Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty