Sharp SRT-8168, SRT-8960, SRT-8040 instruction manual Single Image Recording Setup

Page 34

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SINGLE IMAGE RECORDING

The single image recording function of this VCR can be used to create image data files or animations.

NOTES:

œThe trigger at the 1 SHOT IN terminal should be on for 0.1 sec. or more.

Single Image Recording Setup

1In stop mode, press the REC/PLAY SPEED l (or j) button, to set the recording speed to “000”.

2Press the MENU button to display the MAIN MENU.

3Turn the JOG dial to select the “5.ALARM/SERIES REC SET” line, then turn the SHUTTLE ring clockwise.

øThe (ALARM/SERIES REC SET) menu appears.

<ALARM/SERIES@REC@SET>

*ALARM@SET

@@MODE@@@@@@@@@@@Y1

@@SPEED@@@@@@@@@@8H

@@DURATION@@@@@@@20S

*1@SHOT@SET

@@FIELD@@@@@@@@@@1

@@INTERVAL@@@@@@@1M

*SERIES@REC@@@@@@N

*TAPE@END@OUT@@@@8:00

4Turn the JOG dial until the “FIELD” setting is highlighted, then turn the SHUTTLE ring clockwise.

5Turn the JOG dial to set the number of fields (images) to record every time(1, 2, 3, 4, 5, 10, 30, 60), then turn the SHUTTLE ring clockwise.

6Turn the SHUTTLE ring clockwise.

7Turn the JOG dial to set the interval between each image recording (1M, 2M, 3M), then turn the SHUTTLE ring clockwise.

8Press the MENU EXIT button.

9Press the REC button.

øThe single image recording mode will be activated (the VCR will be in recording stand-by mode).

FPress the REC button one more time, or send a trigger through the 1 SHOT IN terminal on the back panel, to start the single image recording.

œThe trigger interval at the 1 SHOT IN terminal varies according to the number of images to record, but should be over 1 sec.

œAlarm recording is not possible during single image recording.

œDuring the “INTERVAL” period set for single image recording, the WARNING OUT terminal will not be 0 V even if the “NON REC” on the (WARNING OUT/CONTROL SET) menu is set to “Y”.

œIf a single image recording trigger is not received (or if the REC button is not pressed) during the duration set for “INTERVAL”, single image recording will be conducted automatically after the set duration.

œIf a single image recording trigger is received (or if the REC button is pressed) during the duration set for “INTERVAL”, single image recording will be conducted immediately.

œWhen using the 1 SHOT IN terminal, connect a make-contact switch (no voltage) between the 1 SHOT IN and COM terminals.

Recording of set number of images

 

 

 

 

 

 

 

 

 

 

 

 

Input of single

 

 

 

 

 

Input of single image

 

image recording

 

 

 

 

 

recording trigger

 

trigger

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“INTERVAL” setting (1, 2 or 3 minutes)

NOTE:

œIf a setting other than “1” is selected for “FIELD” at step 5, recording will be done in 120-hour mode. The recording speed cannot be modified.

GWhen finished, press the STOP button.

English

33

Page 33 Page 35
Image 34
Page 33 Page 35
Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireFeatures ContentsAccessory Locations of Controls and Indicators Front PanelOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsMain Menu Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Sub-menusON-SCREEN Menu Language Setting Setting the Language and ClockClock setting Automatic Daylight Saving Time Adjustment Setting the Language and ClockFactory setting Selecting the Superimpose Display Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape ManagementOperation If tape management data is present on the tapeTape Management Setting the Tape Management FunctionTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording Speed ModeNormal Recording Before startingRecord Pause Pause/still indicator N flashesNormal Recording Recording CheckAction to Take when the Video Signal Deteriorates Setting the clog detectionClog Detection Setting when not using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording Alarm Recording Setting Alarm RecordingALARM/SERIES REC SET menu appears Alarm Recording Counter Display Alarm RecordingAlarm Recording Reset Function Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Operation Series Recording SetupSeries Recording Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationTape Counter DAY/TIME SearchDay/Time Search Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Quick Method Security LockSelecting Input and Output Terminals Clock AdjustmentConnection Eject output Timer OUT terminal Setting the Cassette Eject ModeCassette Eject Setup Eject input Series in terminalOperator Mode Synchronization ControlSynchronization Control Setting the Cassette Eject ModeAdministrator/Installer Mode SC will flash on the digital displaySetting the Address and Data Transfer Speed Setting for RS-485 or RS-232C USESettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Output Terminals Timer OUT terminalTape END OUT Terminal Output Setting Tape END OUT TerminalOutput Terminals SW OUT Terminal Output SettingSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Connectors SpecificationsGeneral Specifications VideoOther Specifications SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time
Top Page Image Contents