Sears 23897 user manual HOW to Change Console Settings

Page 27

HOW TO CHANGE CONSOLE SETTINGS

The console features a user mode that allows you to view usage information, select a unit of measurement, and adjust the contrast level of the display.

When an iFit module is connected to the console, you can also use the information mode to choose an audio setting for the voice of the personal trainer, set a default menu, check the status of the iFit module, and check for downloads.

1.Select the information mode.

To select the information mode, press and hold down the Display button for a few seconds until the information mode appears in the display.

2.View usage information.

The display will show the total number of hours that the elliptical has been used. The display will also show the total distance (in miles or kilometers) that has been pedaled on the elliptical.

3.Select a unit of measurement if desired.

The word ENGLISH for English miles or the word METRIC for metric kilometers will appear in the display to indicate the currently selected unit of measurement.

To change the unit of measurement, press the Enter button repeatedly to select the desired unit of measurement.

4.Adjust the contrast level of the display if desired.

Press the decrease button to view the contrast level. The currently selected contrast level will appear in the display. Press the 1 Step Ramp increase and decrease buttons to adjust the con- trast level.

5.Determine if an iFit module is connected to the console.

If an iFit module is connected to the console, the display will show the words WIFI MODULE or USB MODULE.

If no module is connected, the display will show the words NO IFIT MODULE. If no module is con- nected, go to step 10.

6.Select an audio setting for the voice of the personal trainer if desired.

Press the decrease button to view the audio setting for the voice of the personal trainer. The currently selected audio setting for the voice of the personal trainer will appear in the display.

To change the audio setting, press the Enter button repeatedly to turn the voice of the personal trainer ON or OFF.

7.Set the default menu if desired.

Press the decrease button to view the default menu setting. The default menu is the menu that will appear when you turn on the console. Press the Enter button repeatedly to select the manual mode menu or the iFit menu as the default menu.

8Check the status of the iFit module if desired.

Press the decrease button to view the iFit sta- tus display. The words CHECK WIFI STATUS or CHECK USB STATUS will appear in the display.

Then, press the Enter button. After a few seconds, the status of the iFit module will appear in the dis- play. To exit this display, press and hold down the Display button for a few seconds.

9.Check for downloads if desired.

Press the decrease button to view the downloads display. The words SEND/RECEIVE DATA will appear in the display.

Then, press the Enter button. The console will then check for iFit workouts and firmware downloads.

10.Exit the information mode.

Press the Display button to exit the information mode.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents QUESTIONS? Model No Serial NoCall TOLL-FREE Table of Contents Important Precautions Before YOU Begin Part Identification Chart Assembly Screws yet Do not press the Top Cover 23 into place yet Upright WireWire with the wire tie Tip Avoid pinching the Upright Wire Avoid pinchingAvoid damaging Tip Avoid damaging the Upright WireTighten the two M6 x 12mm Screws Screws yetSee the lower drawing. Pull upward on See the upper drawing. Locate the Ramp111 Wires Tip Avoid pinching the wires. Attach the RearRepeat this step on the other side Elliptical Repeat this step on the other side of the elliptical See the inset drawing. Locate the Pulse Wire Avoid pinching Wires HOW to Plug in the Power Cord HOW to USE the EllipticalPage HOW to Level the Elliptical HOW to Exercise on the EllipticalFeatures of the Console Console DiagramFollow your progress with the display HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeSame time, the console will not display your Measure your heart rate if desiredHeart rate monitor see page 26 for information About the optional chest heart rate monitorTurn on the fan if desired When you are finished exercising, unplug the power cordHOW to USE AN Onboard Workout Select an onboard workoutBegin pedaling to start the workout Set a calories, distance, or time goal HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit WorkoutMake sure that the iFit module is inserted in the console Select a user Select an iFit workoutHOW to USE the Sound System Follow your progress with the display. See onOptional Chest Heart Rate Monitor HOW to Change Console Settings FCC Information HOW to Calibrate the Ramp Maintenance and TroubleshootingHOW to Adjust the Reed Switch Heart Rate Monitor TroubleshootingHOW to Adjust the Drive Belt Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Description Qty Part ListQty Description Exploded Drawing a Exploded Drawing Drawing C Exploded126 102 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents