Sears 23897 Avoid pinching, Upright Wire, Screws yet Do not press the Top Cover 23 into place yet

Page 7

2.

Orient the Front Stabilizer (3) as shown.

2

 

 

 

 

 

While a second person lifts the front of the

3

100

 

Frame (1), attach the Front Stabilizer (3) with

 

 

two M10 x 120mm Screws (100).

 

 

 

 

1

 

3.

Identify and orient the Upright (5) and the Top

3

 

 

Cover (23) as shown.

 

 

 

 

Slide the Top Cover (23) upward onto the

 

Wire Tie

 

Upright (5).

 

 

 

 

Avoid pinching the

Have a second person hold the Upright (5) and

 

 

 

 

Upright Wire (60)

the Top Cover (23) near the Frame (1).

 

 

 

Locate the wire tie in the Upright (5). Tie the

 

 

5

lower end of the wire tie to the Upright Wire (60).

 

 

 

Next, pull the upper end of the wire tie until the

 

 

23

Upright Wire is routed through the Upright.

 

 

Tip: To prevent the Upright Wire (60) from

 

 

 

falling into the Upright (5), secure the Upright

 

102

 

Wire with the wire tie.

 

 

Tip: Avoid pinching the Upright Wire (60).

 

Wire Tie

 

131

60

Slide the Upright (5) onto the Frame (1).

 

 

1

 

Attach the Upright (5) with eight M8 x 16mm

 

131

 

 

 

Screws (102) and eight M8 Split Washers (131)

 

 

102

(only four of each are shown); do not tighten

 

 

102

131

 

the Screws yet.

 

Do not press the Top Cover (23) into place yet.

7

Image 7
Contents Model No Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Before YOU Begin Part Identification Chart Assembly Screws yet Do not press the Top Cover 23 into place yet Upright WireWire with the wire tie Tip Avoid pinching the Upright Wire Avoid pinchingAvoid damaging Tip Avoid damaging the Upright WireTighten the two M6 x 12mm Screws Screws yetSee the lower drawing. Pull upward on See the upper drawing. Locate the Ramp111 Tip Avoid pinching the wires. Attach the Rear WiresRepeat this step on the other side Elliptical Repeat this step on the other side of the elliptical See the inset drawing. Locate the Pulse Wire Avoid pinching Wires HOW to Plug in the Power Cord HOW to USE the EllipticalPage HOW to Level the Elliptical HOW to Exercise on the EllipticalFeatures of the Console Console DiagramFollow your progress with the display HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeSame time, the console will not display your Measure your heart rate if desiredHeart rate monitor see page 26 for information About the optional chest heart rate monitorTurn on the fan if desired When you are finished exercising, unplug the power cordSelect an onboard workout HOW to USE AN Onboard WorkoutBegin pedaling to start the workout Set a calories, distance, or time goal HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit WorkoutMake sure that the iFit module is inserted in the console Select a user Select an iFit workoutFollow your progress with the display. See on HOW to USE the Sound SystemOptional Chest Heart Rate Monitor HOW to Change Console Settings FCC Information HOW to Calibrate the Ramp Maintenance and TroubleshootingHOW to Adjust the Reed Switch Heart Rate Monitor TroubleshootingHOW to Adjust the Drive Belt Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Description Qty Part ListQty Description Exploded Drawing a Exploded Drawing Drawing C Exploded126 102 Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT