Are the shipping bolts removed?, Not enough, Suds

Are the shipping bolts removed?

All four shipping	bolts must be removed for proper operation	Not enough	water/Not	enough	suds
of the washer.		Low water?
Has a cycle been selected, but START has not been		Low water?
Has a cycle been selected, but START has not been		This washer uses very little water to provide good cleaning
selected and held for 1 second?		This washer uses very little water to provide good cleaning
selected and held for 1 second?		results. You will see little or no water splashing in this washer.
Press and hold	START, for 1 second.
Press and hold	START, for 1 second.	This is normal.
Was the door open after completion of last cycle?		Are you using HE detergent?
The door must be opened and closed again to start a new		Are you using HE detergent?
The door must be opened and closed again to start a new		HE detergent is a low sudsing detergent. This is normal and
cycle.		HE detergent is a low sudsing detergent. This is normal and
cycle.		will not affect cleaning performance.
		will not affect cleaning performance.
Washer continues to fill or drain, cycle seems stuck		Wash/Rinse	temperature
		Wash/Rinse	temperature
Is the top of drain hose lower than 30" (76 cm) on		• Are the hot and cold		water inlet	hoses reversed?
washer?		See "Connect the Inlet Hoses."
		See "Connect the Inlet Hoses."

The top of the drain hose must be at least 30" (76 cm) above

the floor. See "Drain System."

Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe?

The drain hose should be loose yet fit securely. Do not seal

the drain hose with tape. The hose needs an air gap. See "Secure the Drain Hose."

Washer won't drain or spin, water remains in washer

Is the drain hose clogged, or the end of the drain hose more than 96" (2.4 m) above the floor?

msyour voltage low?

Check electrical source or call electrician.

Excessive suds?

Are you washing many loads?

As your frequency of loads washed increases, the water temperature may decrease for hot and warm temperatures. This is normal.

Cycle time changes/Cycle too long

Estimated cycle time?

The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load.

The cycle time will be extended if oversudsing occurs or the load is unbalanced. The SUDs routine removes extra suds

and assures proper rinsing of your garments. The options you select will also affect the cycle times that are shown in the Preset Cycle Settings table.

When excessive suds are detected, a special suds routine automatically starts. Cycle will complete once extra suds are removed. This will occur more frequently when a non-HE detergent is used.

Is the load balanced?

A single or bulky item may cause imbalance. Add more items or redistribute the load.

Excessive suds?

When excessive suds are detected, a special suds routine automatically starts. This routine will add time to the original cycle.

Did the load cause imbalance?

When too much imbalance occurs, an imbalance routine will start to redistribute the load. During the imbalance routine the time displayed may pause until this activity is complete, then resume with the remainder of the cycle.

Are you washing a single item or bulky load?

Spin time is added if an unbalanced load is detected. The washer will attempt to redistribute the load with additional tumbling.

Did you wash a large load on the Express Wash cycle? The Express Wash cycle is designed for smaller load sizes (2-3 items) of lightly soiled garments. If larger loads are washed in this cycle, wash time will be increased.

Did you wash a large load in a gentle or Delicate cycle? When using the Express Wash, or Delicate wash cycles you should use small loads. This ensures a gentle wash for your garments without increasing cycle times.