Hitachi CC14SE OM CUT-OFF Wheel Dismounting and Mounting, Using a Metallic Block Fig

Page 15

English

6. Using a Metallic Block (Fig. 11).

Dimension of workpiece being cut

		Vise (B)
		Metallic block
	Vise (A)	Dimension of
	Vise (A)	metallic block
		metallic block

(Should be slightly smaller than the workpiece being cut)

Fig. 11

When the cut-off wheel has a reduced outer diameter, insert between the vise (A) and (B) a metallic block slightly smaller than the dimension of workpiece being cut to use the cut-off wheel economically.

CUT-OFF WHEEL DISMOUNTING AND MOUNTING

WARNING: Always turn off the trigger switch and disconnect the power plug from the receptacle before dismounting or mounting a wheel, to prevent accidental injury.

1. Dismounting the Cut-Off Wheel (Fig. 12).

Stopper

Hex. bar wrench

Fig. 12

(1)Press the stopper and loosen the bolt with a spanner.

NOTE: When the mounting shaft for cut-off wheel cannot be fixed by pressing the stopper, turn the bolt with a hex. bar wrench while pressing the stopper.

The mounting shaft for cut-off wheel is fixed when the stopper has been lowered.

(2)Remove the bolt, washer (A), and the wheel washer and detach the cut-off wheel.

2.Mounting the Cut-Off Wheel.

Thoroughly remove dust from the wheel washers, washer (A) and bolt, then mount the wheel by following the dismounting procedures in reverse order.

CAUTION:

●Confirm that the stopper has returned to the retract position after installing or removing the cut-off wheel.

●Tighten the bolt so that it doesn’t come loose during operation of the cut-off wheel. Confirm that the bolt has been properly tightened before the power tool is started.

15

Image 15

Contents Advertencia AvertissementContents Table DES MatieresÍndice Meanings of Signal Words Important Safety InformationAlways Secure the Workpiece to the Vise or the Base Safety Safety Rules for Power ToolsSpecific Safety Rules for Use of this Power Tool DO’s DON’Ts Double Insulation for Safer Operation Replacement PartsForeword Polarized PlugsMake Them Available to Other Users Owners of this Tool Part Names SpecificationsTake off the chain InstallationPreparation Before Operation Extension CordSecurely fix the cutting material Before UsingCheck the safety covers for proper operation Confirm the stopper positionPractical Applications Cutting operation Switch operationMoving the stationary vise-jaw Fig Cutting at anglesMounting the Cut-Off Wheel Using a Metallic Block FigCUT-OFF Wheel Dismounting and Mounting Dismounting the Cut-Off Wheel FigInspecting the mounting screws Maintenance and InspectionReplacing a cut-off wheel Inspecting the carbon brushesLubrication Service and RepairsCleaning Service parts listSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéFrançais Choses À Faire Consignes de sécurité spéciales pour cet outil électriqueChoses a NE PAS Faire Avertissement Double Isolation Pour UN Fonctionnement Plus SUR Remplacement DES PiecesAVANT-PROPOS Fiches PolariseesFrançais Spécifications NOM DES PiècesPréparation Avant L’UTILISATION Cordon de rallongeEnlever la chaîne Avant L’UTILISATION Applications Pratiques Opération de coupe Fonctionnement de l’interrupteurCoupes à angle et PrecautionUtilisation d’une cale métallique Fig Déplacement de la mâchoire d’étau fixe FigInstallation ET Retrait DU Disque À Tronçonner Installation du disque à tronçonnerRetrait du disque à tronçonner Fig Inspection des vis de montage Remplacement du disque à tronçonnerEntretien ET Inspection Inspection des balais en carbone etNettoyage Service APRÀS-VENTE ET RépartionsRemisage GraissageSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadEspañol Herramienta Mecánica Acciones Obligatorias Acciones Prohibidas Prologo Piezas DE RepuestoClavijas Polarizadas Español Especificaciones NomenclaturaExtraiga la cadena Preparativos Previos a LA OperaciónInstalación Cordón prolongadorFije firmemente el material de corte Antes DEL USORevise si hay defectos visibles en la rueda de recortar Confirme la posición del topeProcedimiento para fijar el material de corte Figs y Aplicaciones PrácticasVerifique el estado del tomacorriente Funcionamiento de pruebaOperación de corte Operación del interruptorCómo mover la mordaza de tornillo fija Corte a ángulos Figs yMontaje de la rueda de recortar Desmontaje Y Montaje DE LA Rueda DE RecortarUtilización de un bloque metálico Desmontaje de la rueda de recortarInspección de los tornillos de montaje Mantenimiento E InspecciónReemplazo de la rueda de recortar Inspección de las escobillas de carbón Figs.13 yLista de repuestos Servicio Y ReparacionesLubricación LimpiezaPage Hitachi Koki Canada Co