Hitachi CC14SE OM instruction manual Practical Applications

Page 12

English

9.Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power plug fits properly in the electrical receptacle and does not fall out after it is inserted.

Repair or replace the receptacle, if it is faulty.

10.Confirm that the tool’s cabtire power cable is not damaged.

Repair or replace the power cord if an inspection of the cabtire cable indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL, AS FOLLOWS:

11.Trial Run.

After confirming that no one is standing in front of it, step away from the front position and start the power tool and confirm that no operating abnormalities exist before attempting a cutting operation.

Trial run periods:

When replacing the cut-off wheel .......... Over 3 minutes. When starting routine work .................... Over 1 minute.

12.Inspect the rotating stability of the cut-off wheel.

For precise cutting, rotate the cut-off wheel and check for deflection to confirm that the wheel is not noticeably unstable; otherwise vibration might occur and cause an accident.

PRACTICAL APPLICATIONS

WARNING: Never remove or install a workpiece while the cut-off wheel is rotating, to avoide personal injury.

1.Procedure for fixing the cutting material (Fig. 4 and 5).

Quick Vise

Place the workpiece material between Vise (A) and Vise (B), raise the clutch and push the Screw Handle to bring Vise (A) lightly into contact with the workpiece material, as shown in Fig. 4. Then, turn the clutch down, and securely fix the workpiece material in position by turning the Screw Handle. When the cutting job is completed, turn the Screw Handle 2 or 3 times to loosen the vise, and remove the workpiece material, as shown in Fig. 5.

	Workpiece		Workpiece
Vise (B)	material	Vise (B)	material
Vise (A)		Vise (A)
Clutch		Clutch

Screw Handle	Screw Handle
Fig. 4	Fig. 5

12

Image 12

Contents Avertissement AdvertenciaContents Table DES MatieresÍndice Important Safety Information Meanings of Signal WordsSafety Safety Rules for Power Tools Always Secure the Workpiece to the Vise or the BaseSpecific Safety Rules for Use of this Power Tool DO’s DON’Ts Replacement Parts ForewordPolarized Plugs Double Insulation for Safer OperationMake Them Available to Other Users Owners of this Tool Specifications Part NamesInstallation Preparation Before OperationExtension Cord Take off the chainBefore Using Check the safety covers for proper operationConfirm the stopper position Securely fix the cutting materialPractical Applications Switch operation Cutting operationCutting at angles Moving the stationary vise-jaw FigUsing a Metallic Block Fig CUT-OFF Wheel Dismounting and MountingDismounting the Cut-Off Wheel Fig Mounting the Cut-Off WheelMaintenance and Inspection Replacing a cut-off wheelInspecting the carbon brushes Inspecting the mounting screwsService and Repairs CleaningService parts list LubricationInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTFrançais Consignes de sécurité spéciales pour cet outil électrique Choses À FaireChoses a NE PAS Faire Avertissement Remplacement DES Pieces AVANT-PROPOSFiches Polarisees Double Isolation Pour UN Fonctionnement Plus SURFrançais NOM DES Pièces SpécificationsPréparation Avant L’UTILISATION Cordon de rallongeEnlever la chaîne Avant L’UTILISATION Applications Pratiques Fonctionnement de l’interrupteur Opération de coupePrecaution Coupes à angle etDéplacement de la mâchoire d’étau fixe Fig Utilisation d’une cale métallique FigInstallation ET Retrait DU Disque À Tronçonner Installation du disque à tronçonnerRetrait du disque à tronçonner Fig Remplacement du disque à tronçonner Entretien ET InspectionInspection des balais en carbone et Inspection des vis de montageService APRÀS-VENTE ET Répartions RemisageGraissage NettoyageInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónEspañol Herramienta Mecánica Acciones Obligatorias Acciones Prohibidas Prologo Piezas DE RepuestoClavijas Polarizadas Español Nomenclatura EspecificacionesPreparativos Previos a LA Operación InstalaciónCordón prolongador Extraiga la cadenaAntes DEL USO Revise si hay defectos visibles en la rueda de recortarConfirme la posición del tope Fije firmemente el material de corteAplicaciones Prácticas Verifique el estado del tomacorrienteFuncionamiento de prueba Procedimiento para fijar el material de corte Figs yOperación del interruptor Operación de corteCorte a ángulos Figs y Cómo mover la mordaza de tornillo fijaDesmontaje Y Montaje DE LA Rueda DE Recortar Utilización de un bloque metálicoDesmontaje de la rueda de recortar Montaje de la rueda de recortarMantenimiento E Inspección Reemplazo de la rueda de recortarInspección de las escobillas de carbón Figs.13 y Inspección de los tornillos de montajeServicio Y Reparaciones LubricaciónLimpieza Lista de repuestosPage Hitachi Koki Canada Co