Panasonic EY4542 Li-ion Battery Pack EY9L40, Battery Pack Life, Battery Recycling

Page 17

[Battery Pack]

For Appropriate Use of Bat- tery Pack

Li-ion Battery Pack (EY9L40)

For optimum battery life, store the Li-ion bat- tery pack following use without charging it.

When charging the battery pack, confirm that the terminals on the battery charger are free of foreign substances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign sub- stances are found on the terminals.

The life of the battery pack terminals may be affected by foreign substances such as dust and water etc. during operation.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns or a fire.

When operating the battery pack, make sure the work place is well ventilated.

When the battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to prevent dust or dirt from contaminating the battery ter- minals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one.

Battery Recycling

ATTENTION:

FOR Li-ion Battery Pack, EY9L40

A Li-ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERYfor information on how to recycle this battery.

[Battery Charger]

Charging

Cautions for the Li-ion Battery Pack

If the temperature of the battery pack falls approximately below −10°C (14°F), charging will automatically stop to prevent degradation of the battery.

Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack

The ambient temperature range is between 0°C (3°F) and 40°C (104°F).

If the battery pack is used when the battery temperature is below 0°C (3°F), the tool may fail to function properly.

When charging a cool battery pack (below 0°C (3°F)) in a warm place, leave the bat- tery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature.

Cool down the charger when charging more than two battery packs consecutively.

Do not insert your fingers into contact hole, when holding charger or any other occasions.

CAUTION:

To prevent the risk of fire or damage to the bat- tery charger.

Do not use power source from an engine gen- erator.

Do not cover vent holes on the charger and the battery pack.

Unplug the charger when not in use.

- 17 -

Image 17
Contents Model No EY4542 Index/Index/Indice Cubierta de batería Enchufe de carga de batería Ni-MH/Ni-Cd How to Use This Manual II. General Power Tool Safety WarningsWork Area Safety Electrical SafetyBattery Tool Use and Care Personal SafetyPower Tool Use and Care Service IV.FURTHER Safety Instructions for ALL SawsFor ALL Saws Causes and operator prevention of kick- backFor this SAW VI.ADDITIONAL Safety InstructionsWard while the blade is in motion or kick- back may occur Protruding blade may cut objects that can cause kickbackSymbol VII.FOR Battery Charger & Battery PackImportant Safety Instructions Symbol MeaningAmperes AWG Size of Cord Equal to or But less VIII.ASSEMBLYAttaching or Removing Battery Pack IX.OPERATION Before Using the ToolFollow these steps Installing BladeRemoving Blade Alignment with cutting line Using the ToolSwitch lock lever Handle Front grip Rip fence EY3500B7727 Cutting depth adjustmentCollecting Dust Rip fenceControl Panel Battery low warning lampLED light Overheat warning lampCutting thin or corrugated materials For Proper Use Further DetailCutting large sheets Page Battery Pack Life Li-ion Battery Pack EY9L40Battery Recycling Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery PackMay flash quickly to indicate the charging is completed Li-ion Battery PackNi-MH/Ni-Cd Battery Pack Cleaning Tool MaintenanceTransparent Guard Lamp IndicationsXII.SPECIFICATIONS XI.ACCESSORIESWeight with battery pack EY9L40 Overall lengthNi-Cd/Ni-MH battery pack Li-ion battery packCharging time EY9107Gardez la zone de travail propre et bien aérée Sécurité de la zone de travailLes endroits encombrés et sombres invitent les accidents Les distractions peuvent faire perdre le con- trôleSécurité personnelle Sécurité électriqueUtilisation et soins de loutil mécanique ’utilisation d’un RCD réduit les risques d’électrocutionRéparation Utilisation et soins de la batterie de loutilMaintenez les outils de coupe affûtés et propres Ceci assure le maintien de la sécurité de loutil mécaniqueNutilisez pas de lames émoussées ou endommagées DE Sécurité PourCauses et prévention par lutilisateur dun retour Rite Generales SymboleSymbole Signification Avertissement Instructions de sécurité impor­ tantesEgal ou Mais Norme d’entrée AmpèresSupérieur à Inférieur à Ne modifiez la fiche en aucune façonIX.UTILISATION VIII.MONTAGEFixation ou retrait de la batterie autonome Avant d’utiliser l’outilPage Ci-dessous Procéder suivant les étapes indiquéesDessous Procéder suivant les étapes indiquées ciVérifiez que le levier du verrou du commutateur marche Utilisation de l’outilSuivez ces étapes Ramassage de la poussière Ajustement de la profondeur de sciageGuide de sciage EY3500B7727 Témoin d’avertissement de surchauffe Panneau de commandeLumière DEL Témoin d’avertissement de batterie bassePour éviter de se blesser gravement Avertissement Pour une batterie autonome Li-ion EY9L40 Précautions à prendre pour la bat- terie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Indication du voyant EntretienNettoyage de l’outil Protège-lame transparent Batterie autonome Li-ion XII.FICHE TechniqueChargement EY9168 EY9188 EY9107 EY9136 EY9108 Batterie autonome Ni-MH/Ni-CdII. Advertencias DE IntroducciónForma de utilizar este manual Seguridad del área de trabajoUso y cuidados de herramientas eléctricas Seguridad personalEl uso del RCD reduce el riesgo de cho- ques eléctricos Mantenga las herramientas eléctricasUso y cuidado de la herramienta a batería III.INSTRUCCIONES DEServicio Mantenga las herramientas de corte afi- ladas y limpiasCausas y prevención de retroceso del operador IV.INSTRUCCIONES DEInstrucciones DE Símbolo VI.REGLAS DE SEGURI­Dañadas, depósitos pegajosos o acumulación de residuos Símbolo SignificadoEspec. entrada Amperios Instrucciones de seguridad im­ portantesDe CA Igual o mayor Pero meIX.OPERACIÓN VIII. MontajeColocación y extracción de la batería Antes de usar la herramientaAdvertencia Desmontaje de la cuchilla Instalación de la cuchillaSiga estos pasos Extraiga el paquete de baterías de la herrami- entaSiga los pasos siguientes Uso de la herramientaAlineación con la línea de corte Guía de corte EY3500B7727 Ajuste de la profundidad del corteRecolección del polvo Tuerca de Apriete Ajuste de Profundidad Despliegue abajoLuz LED Panel de controleLuz de advertencia de sobrecalenta­ miento Luz de advertencia de batería bajaCorte de hojas grandes Utilización adecuada detalles adicionalesAdvertencia Vida útil de la batería Batería de Li-ión EY9L40Reciclado de la batería Precauciones para el paquete de baterías de Li-iónBatería Ni-MH/Ni-Cd Indicación de la lámpara MantenimientoLimpieza de la herramienta Protector transparente XI.ACCESORIOSBatería de Li-ión XII.ESPECIFICACIONESCarga EY9168 EY9188 EY9107 EY9136 EY9108 Batería Ni-MH/Ni-CdEY981045421 H2009 One Panasonic Way, Secaucus, New Jersey
Related manuals
Manual 212 pages 27.89 Kb