Panasonic EY4542 operating instructions Li-ion Battery Pack, Ni-MH/Ni-Cd Battery Pack

Page 18

Li-ion Battery Pack

NOTE:

Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use.

Battery charger (EY0L80)

1.Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.

2.Insert the battery pack firmly into the charger.

1Line up the alignment marks and place the battery onto the dock on the charger.

2Slide forward in the direction of the arrow.

Alignment marks

3.During charging, the charging lamp will be lit. When charging is completed, an internal electronic switch will automatically be trig- gered to prevent overcharging.

Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation).

The orange standby lamp will be flashing until the battery cools down.

Charging will then begin automatically.

4.The charge lamp (green) will flash slowly once the battery is approximately 80% charged.

5.When charging is completed, the charging lamp will start flashing quickly in green color.

6.If the temperature of the battery pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time. Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal operating tem- perature.

7.If the power lamp does not light immediate- ly after the charger is plugged in, or if after the standard charging time the charging lamp does not flash quickly in green, consult an authorized dealer.

8.If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charging lamp

may flash quickly to indicate the charging is completed.

Ni-MH/Ni-Cd Battery Pack

NOTE:

When you charge the battery pack for the first time, or after prolonged storage, charge it for about 24 hours to bring the battery up to full capacity.

Battery charger (EY0L80)

1.Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.

2.Insert the battery pack firmly into the charger.

3.During charging, the charging lamp will be lit. When charging is completed, an internal electronic switch will automatically be trig- gered to prevent overcharging.

Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation).

The orange standby lamp will be flashing until the battery cools down. Charging will then begin automatically.

4.When charging is completed, the charging lamp will start flashing quickly in green color.

5.If the charging lamp does not light immediate- ly after the charger is plugged in, or if after the standard charging time the charging lamp does not flash quickly in green, consult an authorized dealer.

6.If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charging lamp may flash quickly to indicate the charging is completed.

- 18 -

Image 18
Contents Model No EY4542 Index/Index/Indice Cubierta de batería Enchufe de carga de batería Ni-MH/Ni-Cd Work Area Safety II. General Power Tool Safety WarningsHow to Use This Manual Electrical SafetyPersonal Safety Power Tool Use and CareBattery Tool Use and Care For ALL Saws IV.FURTHER Safety Instructions for ALL SawsService Causes and operator prevention of kick- backWard while the blade is in motion or kick- back may occur VI.ADDITIONAL Safety InstructionsFor this SAW Protruding blade may cut objects that can cause kickbackImportant Safety Instructions VII.FOR Battery Charger & Battery PackSymbol Symbol MeaningVIII.ASSEMBLY Attaching or Removing Battery PackAmperes AWG Size of Cord Equal to or But less Before Using the Tool IX.OPERATIONInstalling Blade Removing BladeFollow these steps Using the Tool Switch lock lever Handle Front gripAlignment with cutting line Collecting Dust Cutting depth adjustmentRip fence EY3500B7727 Rip fenceLED light Battery low warning lampControl Panel Overheat warning lampFor Proper Use Further Detail Cutting large sheetsCutting thin or corrugated materials Page Battery Recycling Li-ion Battery Pack EY9L40Battery Pack Life Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery PackLi-ion Battery Pack Ni-MH/Ni-Cd Battery PackMay flash quickly to indicate the charging is completed Transparent Guard MaintenanceCleaning Tool Lamp IndicationsWeight with battery pack EY9L40 XI.ACCESSORIESXII.SPECIFICATIONS Overall lengthCharging time Li-ion battery packNi-Cd/Ni-MH battery pack EY9107Les endroits encombrés et sombres invitent les accidents Sécurité de la zone de travailGardez la zone de travail propre et bien aérée Les distractions peuvent faire perdre le con- trôleUtilisation et soins de loutil mécanique Sécurité électriqueSécurité personnelle ’utilisation d’un RCD réduit les risques d’électrocutionMaintenez les outils de coupe affûtés et propres Utilisation et soins de la batterie de loutilRéparation Ceci assure le maintien de la sécurité de loutil mécaniqueDE Sécurité Pour Causes et prévention par lutilisateur dun retourNutilisez pas de lames émoussées ou endommagées Symbole Symbole SignificationRite Generales Instructions de sécurité impor­ tantes AvertissementSupérieur à Inférieur à Norme d’entrée AmpèresEgal ou Mais Ne modifiez la fiche en aucune façonFixation ou retrait de la batterie autonome VIII.MONTAGEIX.UTILISATION Avant d’utiliser l’outilPage Dessous Procéder suivant les étapes indiquéesCi-dessous Procéder suivant les étapes indiquées ciUtilisation de l’outil Suivez ces étapesVérifiez que le levier du verrou du commutateur marche Ajustement de la profondeur de sciage Guide de sciage EY3500B7727Ramassage de la poussière Lumière DEL Panneau de commandeTémoin d’avertissement de surchauffe Témoin d’avertissement de batterie bassePour éviter de se blesser gravement Avertissement Précautions à prendre pour la bat- terie autonome Li-ion Pour une batterie autonome Li-ion EY9L40Batterie autonome Ni-MH/Ni-Cd Entretien Nettoyage de l’outilIndication du voyant Protège-lame transparent XII.FICHE Technique Batterie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Chargement EY9168 EY9188 EY9107 EY9136 EY9108Forma de utilizar este manual IntroducciónII. Advertencias DE Seguridad del área de trabajoEl uso del RCD reduce el riesgo de cho- ques eléctricos Seguridad personalUso y cuidados de herramientas eléctricas Mantenga las herramientas eléctricasServicio III.INSTRUCCIONES DEUso y cuidado de la herramienta a batería Mantenga las herramientas de corte afi- ladas y limpiasIV.INSTRUCCIONES DE Instrucciones DECausas y prevención de retroceso del operador Dañadas, depósitos pegajosos o acumulación de residuos VI.REGLAS DE SEGURI­Símbolo Símbolo SignificadoDe CA Instrucciones de seguridad im­ portantesEspec. entrada Amperios Igual o mayor Pero meColocación y extracción de la batería VIII. MontajeIX.OPERACIÓN Antes de usar la herramientaAdvertencia Siga estos pasos Instalación de la cuchillaDesmontaje de la cuchilla Extraiga el paquete de baterías de la herrami- entaUso de la herramienta Alineación con la línea de corteSiga los pasos siguientes Recolección del polvo Ajuste de la profundidad del corteGuía de corte EY3500B7727 Tuerca de Apriete Ajuste de Profundidad Despliegue abajoLuz de advertencia de sobrecalenta­ miento Panel de controleLuz LED Luz de advertencia de batería bajaUtilización adecuada detalles adicionales Corte de hojas grandesAdvertencia Reciclado de la batería Batería de Li-ión EY9L40Vida útil de la batería Precauciones para el paquete de baterías de Li-iónBatería Ni-MH/Ni-Cd Mantenimiento Limpieza de la herramientaIndicación de la lámpara XI.ACCESORIOS Protector transparenteXII.ESPECIFICACIONES Batería de Li-iónBatería Ni-MH/Ni-Cd Carga EY9168 EY9188 EY9107 EY9136 EY9108One Panasonic Way, Secaucus, New Jersey EY981045421 H2009
Related manuals
Manual 212 pages 27.89 Kb