Panasonic EY4542 operating instructions Viii.Assembly, Attaching or Removing Battery Pack

Page 9

b. extension cord is properly wired and in good electrical condition.

c. wire size is large enough for ampere rating of charger as specified below.

RECOMMENDED MINIMUM AWG SIZE OF

EXTENSION CORDS FOR

BATTERY CHARGERS

AC Input Rating.

Amperes

AWG Size of Cord

Equal to or

But less

Length of Cord,

 

greater than

than

Feet

 

 

 

 

 

25

50

100 150

0

2

18

18

18

16

8)Do not operate charger with damaged cord or plug-replace them immediately.

9)Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified service personnel.

10)Do not disassemble charger; take it to a qualified service personnel when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

11)To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.

12) The charger and battery pack are specifically designed to work together. Do not attempt to charge any other cordless tool or battery pack with this charger.

13)Do not attempt to charge the battery pack with any other charger.

14)Do not attempt to disassemble the battery pack housing.

15)Do not store the tool and battery pack in locations where the temperature may reach or exceed 50°C (122°F) (such as a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery.

16) Do not charge battery pack when the temperature is BELOW 0°C (32°F) or ABOVE 40°C (104°F). This is very important in order to maintain optimal condition of the battery pack.

17)Do not incinerate the battery pack. It can explode in a fire.

18)Avoid dangerous environment. Do not use charger in damp or wet locations.

19)The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage!

20)Do not abuse cord. Never carry charger by cord or yank it to disconnect from outlet. Keep cord away from heat, oil and sharp edges.

21)Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, etc., while charging.

22)Use of an attachment not recommended may result in a risk of fire, electric shock, or personal injury.

23)Do not short the battery pack. A battery short can cause a large current flow, over heating and create the risk of fire or personal injury.

24)NOTE: If the supply cord of this appliance is damaged, it must only be replaced by a repair shop authorized by the manufacturer, because special purpose tools are required.

25)TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER).

This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper out- let. Do not change the plug in any way.

VIII.ASSEMBLY

Attaching or Removing Battery Pack

CAUTION:

Before inserting battery pack, check that the power switch in the tool actuates properly and returns to the “OFF” position when released.

1.To connect the battery pack (See Fig. 2)

Line up the alignment marks and attach the battery pack.

Slide the battery pack until it locks into posi- tion.

Alignment marks

Fig. 2

- -

Image 9
Contents Model No EY4542 Index/Index/Indice Cubierta de batería Enchufe de carga de batería Ni-MH/Ni-Cd How to Use This Manual II. General Power Tool Safety WarningsWork Area Safety Electrical SafetyPersonal Safety Power Tool Use and CareBattery Tool Use and Care Service IV.FURTHER Safety Instructions for ALL SawsFor ALL Saws Causes and operator prevention of kick- backFor this SAW VI.ADDITIONAL Safety InstructionsWard while the blade is in motion or kick- back may occur Protruding blade may cut objects that can cause kickbackSymbol VII.FOR Battery Charger & Battery PackImportant Safety Instructions Symbol MeaningVIII.ASSEMBLY Attaching or Removing Battery PackAmperes AWG Size of Cord Equal to or But less IX.OPERATION Before Using the ToolInstalling Blade Removing BladeFollow these steps Using the Tool Switch lock lever Handle Front gripAlignment with cutting line Rip fence EY3500B7727 Cutting depth adjustmentCollecting Dust Rip fenceControl Panel Battery low warning lampLED light Overheat warning lampFor Proper Use Further Detail Cutting large sheetsCutting thin or corrugated materials Page Battery Pack Life Li-ion Battery Pack EY9L40Battery Recycling Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery PackLi-ion Battery Pack Ni-MH/Ni-Cd Battery PackMay flash quickly to indicate the charging is completed Cleaning Tool MaintenanceTransparent Guard Lamp IndicationsXII.SPECIFICATIONS XI.ACCESSORIESWeight with battery pack EY9L40 Overall lengthNi-Cd/Ni-MH battery pack Li-ion battery packCharging time EY9107Gardez la zone de travail propre et bien aérée Sécurité de la zone de travailLes endroits encombrés et sombres invitent les accidents Les distractions peuvent faire perdre le con- trôleSécurité personnelle Sécurité électriqueUtilisation et soins de loutil mécanique ’utilisation d’un RCD réduit les risques d’électrocutionRéparation Utilisation et soins de la batterie de loutilMaintenez les outils de coupe affûtés et propres Ceci assure le maintien de la sécurité de loutil mécaniqueDE Sécurité Pour Causes et prévention par lutilisateur dun retourNutilisez pas de lames émoussées ou endommagées Symbole Symbole SignificationRite Generales Avertissement Instructions de sécurité impor­ tantesEgal ou Mais Norme d’entrée AmpèresSupérieur à Inférieur à Ne modifiez la fiche en aucune façonIX.UTILISATION VIII.MONTAGEFixation ou retrait de la batterie autonome Avant d’utiliser l’outilPage Ci-dessous Procéder suivant les étapes indiquéesDessous Procéder suivant les étapes indiquées ciUtilisation de l’outil Suivez ces étapesVérifiez que le levier du verrou du commutateur marche Ajustement de la profondeur de sciage Guide de sciage EY3500B7727Ramassage de la poussière Témoin d’avertissement de surchauffe Panneau de commandeLumière DEL Témoin d’avertissement de batterie bassePour éviter de se blesser gravement Avertissement Pour une batterie autonome Li-ion EY9L40 Précautions à prendre pour la bat- terie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Entretien Nettoyage de l’outilIndication du voyant Protège-lame transparent Batterie autonome Li-ion XII.FICHE TechniqueChargement EY9168 EY9188 EY9107 EY9136 EY9108 Batterie autonome Ni-MH/Ni-CdII. Advertencias DE IntroducciónForma de utilizar este manual Seguridad del área de trabajoUso y cuidados de herramientas eléctricas Seguridad personalEl uso del RCD reduce el riesgo de cho- ques eléctricos Mantenga las herramientas eléctricasUso y cuidado de la herramienta a batería III.INSTRUCCIONES DEServicio Mantenga las herramientas de corte afi- ladas y limpiasIV.INSTRUCCIONES DE Instrucciones DECausas y prevención de retroceso del operador Símbolo VI.REGLAS DE SEGURI­Dañadas, depósitos pegajosos o acumulación de residuos Símbolo SignificadoEspec. entrada Amperios Instrucciones de seguridad im­ portantesDe CA Igual o mayor Pero meIX.OPERACIÓN VIII. MontajeColocación y extracción de la batería Antes de usar la herramientaAdvertencia Desmontaje de la cuchilla Instalación de la cuchillaSiga estos pasos Extraiga el paquete de baterías de la herrami- entaUso de la herramienta Alineación con la línea de corteSiga los pasos siguientes Guía de corte EY3500B7727 Ajuste de la profundidad del corteRecolección del polvo Tuerca de Apriete Ajuste de Profundidad Despliegue abajoLuz LED Panel de controleLuz de advertencia de sobrecalenta­ miento Luz de advertencia de batería bajaCorte de hojas grandes Utilización adecuada detalles adicionalesAdvertencia Vida útil de la batería Batería de Li-ión EY9L40Reciclado de la batería Precauciones para el paquete de baterías de Li-iónBatería Ni-MH/Ni-Cd Mantenimiento Limpieza de la herramientaIndicación de la lámpara Protector transparente XI.ACCESORIOSBatería de Li-ión XII.ESPECIFICACIONESCarga EY9168 EY9188 EY9107 EY9136 EY9108 Batería Ni-MH/Ni-CdEY981045421 H2009 One Panasonic Way, Secaucus, New Jersey
Related manuals
Manual 212 pages 27.89 Kb