Panasonic EY7546 Recommended Grip, Battery Pack For Appropriate Use of Bat­ tery Pack

Page 10

(4) Battery low warning lamp

Off (normal

Flashing (No charge)

operation)

Battery protection

 

feature active

Excessive (complete) discharging of lithium ion batteries shortens their service life dramatically. The driver includes a battery protection feature designed to prevent excessive discharging of the battery pack.

• The battery protection feature activates immediately before the battery loses its charge, causing the battery low warning lamp to flash.

• If you notice the battery low warning lamp flashing, charge the battery pack immediately.

Recommended Grip

Use the grip to hold and operate the driver with one hand. If the job requires additional force, you can push against the rear end of the driver with your other hand.

[Battery Pack]

For Appropriate Use of Bat­ tery Pack

Li­ion Battery Pack

For optimum battery life, store the Li-ion bat- tery pack following use without charging it.

When charging the battery pack, confirm that the terminals on the battery charger are free of foreign substances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign substances are found on the ter- minals.

The life of the battery pack terminals may be affected by foreign substances such as dust and water etc. during operation.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a con- nection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns or a fire.

When operating the battery pack, make sure the work place is well ventilated.

When the battery pack is removed from the main body of the tool, replace the battery

pack cover immediately in order to prevent dust or dirt from contaminating the battery terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a lim- ited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one.

Battery Recycling

ATTENTION:

FOR Li­ion Battery Pack

A Li-ion battery that is recyclable powers the product you have purchased. Please call 1­800­ 8­BATTERY for information on how to recycle this battery.

[Battery Charger]

Charging

CAUTION:

If the temperature of the battery pack falls approximately below −10°C (14°F), charg- ing will automatically stop to prevent degra- dation of the battery.

The ambient temperature range is between 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the bat- tery temperature is below 0°C (32°F), the tool may fail to function properly.

When charging a cool battery pack (below 0°C (32°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature.

Cool down the charger when charging more than two battery packs consecutively.

Do not insert your fingers into contact hole, when holding charger or any other occasions.

To prevent the risk of fire or damage to the battery charger.

Do not use power source from an engine generator.

Do not cover vent holes on the charger and the battery pack.

Unplug the charger when not in use.

Image 10
Contents Model No EY7546/EY7547 EY7550/EY7551 ImportanteBattery low warning lamp Index/Index/IndiceLimited Warranty General Safety RulesDefinition of IP code Battery Tool Use and Care II. Specific Safety RulesPower Tool Use and Care ServiceImportant Safety Instructions Battery PackSymbol Meaning Amperes AWG Size of Cord Equal to or But less Attaching or Removing Bit IV. AssemblyAttaching or Removing Battery­ Pack Attaching or Removing Socket­Operation Control Panel 4 Recommended work guideline tableBattery Charger Charging Battery Pack For Appropriate Use of Bat­ tery PackRecommended Grip Lamp Indications Factors Affecting Tighten­ ing Torque VI. MaintenanceVII. Tightening Torque Bolt Tightening ConditionsEY7550 Specifications VIII. AccessoriesIX. Appendix Battery Charger Federal Communication Commission Interference StatementConservez CES INSTRUC­ Tions Définitions des codes IPGarantie Limitée Sécurité de la zone de travailUtilisation et soins de l’outil méca­nique Sécurité personnelleMaintenez les outils de coupe affûtés et propres Utilisation et soins de la batterie de l’outil RéparationInstructions de sécurité importantes­ Symbole SignificationAvertissement Avertissement Fixation ou retrait de la douille IV. MontageFixation ou retrait d’une mèche Fixation ou retrait de la batterie­ autonomeComment utiliser le cro­ chet de ceinture Corps principalUtilisation du commutateur pour une rotation en sens normal Sélection du mode de puissance de percussion Pour changer le côté d’installation du crochet de ceinturePanneau de commande Tableau de référence des travaux recommandés­Batterie Tenue recommandéeBatterie autonome Li-ion Longévité des batteries autonomes Chargeur de batterie RechargeMise EN Garde Recyclage de la batterie autonomeIndication DU Voyant Facteurs affectant le cou­ ple de serrage VI. EntretienVII. Couple DE SERRAGE­ Conditions de serrage des boulons EY7546EY7550 EY7551IX. Appendice VIII. AccessoiresCapacites Maximum Recommandees Caracteristiques TechniquesBatterie Autonome EY9L44 EY9L50 Durée de chargementGuarde Estas INSTRUC­ Ciones Definición del código IPGarantía Limitada Seguridad del lugar de trabajoUso y cuidados de herramientas eléctricas Seguridad personalMantenga las herramientas de corte afiladas y limpias Uso y cuidado de la herramienta a batería Servicio¡ADVERTENCIA LA BateriaInstrucciones de seguridad importantes­ Guarde Estas InstruccionesAdvertencia Instalación o desmontaje del cubo IV. MontajeColocación o extracción de la broca NotaCuerpo principal FuncionamientoColocación y extracción de la batería Funcionamiento del inter­ ruptor de rotación de avancePanel de controle Cómo utilizar el gancho del cinturónPara cambiar el lugar de ubicación del gancho de cinturón Selección de modo de potencia de impactoLuz de advertencia de sobrecalenta­ miento Luz LEDCuadro de guías de trabajo reco­ mendadas Batería de Li­ión Empuñadura recomendadaBloque de pilas Para un uso adecuado de la batería Vida útil de la bateríaCargador de la batería Carga PrecauciónVII. PAR DE Apriete VI. MantenimientoFactores que afectan al par de apriete Condiciones de apriete de pernos EY7546 M10 x 35 mm. M12, M14, M16 x 45 mm MPerno estándar kgf-cm IX. Anexo VIII. AccesoriosEspecificaciones Cargador DE Batería EY9L44 EY9L50 Tiempo de cargaMemo Panasonic Consumer Electronics Company