Panasonic EY7546 IV. Assembly, Attaching or Removing Bit, Attaching or Removing Socket­

Page 7

Never use other than the dedicated char- ger to charge the battery pack. Otherwise, the battery may leak, overheat, or explode.

After removing the battery pack from the tool or the charger, always reattach the pack cover. Otherwise, the battery con- tacts could be shorted, leading to a risk of fire.

When the Battery Pack Has Deteriorated, Replace It with a New One.

Continued use of a damaged battery pack may result in heat generation, ignition or battery rupture.

IV. ASSEMBLY

Attaching or Removing Bit

NOTE:

When attaching or removing a bit, discon- nect battery pack from tool or place the switch in the center position (switch lock).

1.Hold the collar of quick connect chuck and pull it out from the driver.

2.Insert the bit into the chuck. Release the collar.

3.The collar will return to its original position when it is released.

4.Pull the bit to make sure it does not come out.

5.To remove the bit, pull out the collar in the same way.

CAUTION:

If the collar does not return to its origi- nal position or the bit comes out when pulled on, the bit has not been properly attached. Make sure the bit is properly attached before use.

Use 6.35 mm (1/4") hexagonal bits.

To ensure proper securement of the bit, use only hexagonal bits with 9.5 mm (3/8") detent.

6.35 mm (1/4")

9.5 mm (3/8")

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attaching or Removing Socket­

1.Attaching Socket

Attach the socket by sliding the female detent on the bottom of the socket to the square drive on the body.

Make sure the socket is firmly connected to the body.

2.Removing Socket Pull out the socket.

NOTE:

Attaching or Removing Original Options and Sockets

Keep the body above freezing point (0°C 32°F) when attach or detach original options and sockets to the square drive on the body. The cushion rubber in the square drive to push up the ball may get hard under freezing point. This requires extra force in detaching and attaching sockets.

Attaching or Removing Battery­ Pack

1.To connect the battery pack:

Line up the alignment marks and attach the battery pack.

Slide the battery pack until it locks into position.

Alignment marks

2.To remove the battery pack:

Pull the button from the front to release the battery pack.

Button

Image 7
Contents Importante Model No EY7546/EY7547 EY7550/EY7551Index/Index/Indice Battery low warning lampLimited Warranty General Safety RulesDefinition of IP code Service II. Specific Safety RulesPower Tool Use and Care Battery Tool Use and CareImportant Safety Instructions Battery PackSymbol Meaning Amperes AWG Size of Cord Equal to or But less Attaching or Removing Socket­ IV. AssemblyAttaching or Removing Battery­ Pack Attaching or Removing BitOperation Recommended work guideline table Control Panel 4Battery Charger Charging Battery Pack For Appropriate Use of Bat­ tery PackRecommended Grip Lamp Indications Bolt Tightening Conditions VI. MaintenanceVII. Tightening Torque Factors Affecting Tighten­ ing TorqueEY7550 Specifications VIII. AccessoriesIX. Appendix Federal Communication Commission Interference Statement Battery ChargerSécurité de la zone de travail Définitions des codes IPGarantie Limitée Conservez CES INSTRUC­ TionsUtilisation et soins de l’outil méca­nique Sécurité personnelleMaintenez les outils de coupe affûtés et propres Réparation Utilisation et soins de la batterie de l’outilInstructions de sécurité importantes­ Symbole SignificationAvertissement Avertissement Fixation ou retrait de la batterie­ autonome IV. MontageFixation ou retrait d’une mèche Fixation ou retrait de la douilleComment utiliser le cro­ chet de ceinture Corps principalUtilisation du commutateur pour une rotation en sens normal Tableau de référence des travaux recommandés­ Pour changer le côté d’installation du crochet de ceinturePanneau de commande Sélection du mode de puissance de percussionBatterie Tenue recommandéeBatterie autonome Li-ion Recyclage de la batterie autonome Chargeur de batterie RechargeMise EN Garde Longévité des batteries autonomesIndication DU Voyant Conditions de serrage des boulons EY7546 VI. EntretienVII. Couple DE SERRAGE­ Facteurs affectant le cou­ ple de serrageEY7551 EY7550Caracteristiques Techniques VIII. AccessoiresCapacites Maximum Recommandees IX. AppendiceEY9L44 EY9L50 Durée de chargement Batterie AutonomeSeguridad del lugar de trabajo Definición del código IPGarantía Limitada Guarde Estas INSTRUC­ CionesUso y cuidados de herramientas eléctricas Seguridad personalMantenga las herramientas de corte afiladas y limpias Servicio Uso y cuidado de la herramienta a bateríaGuarde Estas Instrucciones LA BateriaInstrucciones de seguridad importantes­ ¡ADVERTENCIAAdvertencia Nota IV. MontajeColocación o extracción de la broca Instalación o desmontaje del cuboFuncionamiento del inter­ ruptor de rotación de avance FuncionamientoColocación y extracción de la batería Cuerpo principalSelección de modo de potencia de impacto Cómo utilizar el gancho del cinturónPara cambiar el lugar de ubicación del gancho de cinturón Panel de controleLuz de advertencia de sobrecalenta­ miento Luz LEDCuadro de guías de trabajo reco­ mendadas Vida útil de la batería Empuñadura recomendadaBloque de pilas Para un uso adecuado de la batería Batería de Li­iónPrecaución Cargador de la batería CargaVII. PAR DE Apriete VI. MantenimientoFactores que afectan al par de apriete Condiciones de apriete de pernos EY7546 M10 x 35 mm. M12, M14, M16 x 45 mm MPerno estándar kgf-cm IX. Anexo VIII. AccesoriosEspecificaciones EY9L44 EY9L50 Tiempo de carga Cargador DE BateríaMemo Panasonic Consumer Electronics Company