Panasonic EY7546 operating instructions Lamp Indications

Page 11

NOTE:

Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use.

Battery charger

1.Plug the charger into the AC outlet.

2.Insert the battery pack firmly into the charger.

1Line up the alignment marks and place the battery onto the dock on the charger.

2Slide forward in the direction of the arrow.

Alignment marks

3.During charging, the charging lamp will be lit.

When charging is completed, an internal electronic switch will automatically be trig- gered to prevent overcharging.

Charging will not start if the battery pack is warm (for example, immediately after heavy-duty operation).

The orange standby lamp will be flash- ing until the battery cools down. Charging will then begin automatically.

4.The charge lamp (green) will flash slowly once the battery is approximately 80% charged.

5.When charging is completed, the charging lamp in green color will turn off.

6.If the temperature of the batter pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time.

Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal operat- ing temperature.

7.Consult an authorized dealer if the charging lamp (green) does not turn off.

8.If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charg- ing lamp in green color will turn off.

9.Remove the battery pack while the battery pack release button is held up.

Battery pack release button

LAMP INDICATIONS

 

 

 

 

 

 

Charging is completed. (Full charge.)

 

 

 

 

 

 

Battery is approximately 80% charged.

 

 

 

 

 

 

 

 

 

 

 

 

Now charging.

 

 

 

 

 

 

 

 

 

 

 

 

Charger is plugged into the AC outlet. Ready to charge.

 

 

 

 

 

 

 

 

(Green)

(Orange)

Charging Status Lamp.

 

 

 

 

 

 

Left: green Right: orange will be displayed.

 

 

 

 

 

 

 

 

 

 

 

 

Battery pack is cool.

 

 

 

 

 

 

 

 

 

 

 

 

The battery pack is being charged slowly to reduce the load on the battery.

 

 

 

 

 

 

 

 

 

 

 

 

Battery pack is warm.

 

 

 

 

 

 

 

 

 

 

 

 

Charging will begin when temperature of battery pack drops. If the temperature of the

 

 

 

 

 

 

 

 

 

 

 

 

battery pack is -10° or less, the charging status lamp (orange) will also start flashing .

 

 

 

 

 

 

Charging will begin when the temperature of the battery pack goes up"

 

 

 

 

 

 

Charging is not possible. Clogged with dust or malfunction of the bat-

 

 

 

 

 

 

tery pack.

Turn off

Lit

Flashing

Image 11
Contents Importante Model No EY7546/EY7547 EY7550/EY7551Index/Index/Indice Battery low warning lampDefinition of IP code General Safety RulesLimited Warranty Service II. Specific Safety RulesPower Tool Use and Care Battery Tool Use and CareSymbol Meaning Battery PackImportant Safety Instructions Amperes AWG Size of Cord Equal to or But less Attaching or Removing Socket­ IV. AssemblyAttaching or Removing Battery­ Pack Attaching or Removing BitOperation Recommended work guideline table Control Panel 4Recommended Grip Battery Pack For Appropriate Use of Bat­ tery PackBattery Charger Charging Lamp Indications Bolt Tightening Conditions VI. MaintenanceVII. Tightening Torque Factors Affecting Tighten­ ing TorqueEY7550 IX. Appendix VIII. AccessoriesSpecifications Federal Communication Commission Interference Statement Battery ChargerSécurité de la zone de travail Définitions des codes IPGarantie Limitée Conservez CES INSTRUC­ TionsMaintenez les outils de coupe affûtés et propres Sécurité personnelleUtilisation et soins de l’outil méca­nique Réparation Utilisation et soins de la batterie de l’outilAvertissement Symbole SignificationInstructions de sécurité importantes­ Avertissement Fixation ou retrait de la batterie­ autonome IV. MontageFixation ou retrait d’une mèche Fixation ou retrait de la douilleUtilisation du commutateur pour une rotation en sens normal Corps principalComment utiliser le cro­ chet de ceinture Tableau de référence des travaux recommandés­ Pour changer le côté d’installation du crochet de ceinturePanneau de commande Sélection du mode de puissance de percussionBatterie autonome Li-ion Tenue recommandéeBatterie Recyclage de la batterie autonome Chargeur de batterie RechargeMise EN Garde Longévité des batteries autonomesIndication DU Voyant Conditions de serrage des boulons EY7546 VI. EntretienVII. Couple DE SERRAGE­ Facteurs affectant le cou­ ple de serrageEY7551 EY7550Caracteristiques Techniques VIII. AccessoiresCapacites Maximum Recommandees IX. AppendiceEY9L44 EY9L50 Durée de chargement Batterie AutonomeSeguridad del lugar de trabajo Definición del código IPGarantía Limitada Guarde Estas INSTRUC­ CionesMantenga las herramientas de corte afiladas y limpias Seguridad personalUso y cuidados de herramientas eléctricas Servicio Uso y cuidado de la herramienta a bateríaGuarde Estas Instrucciones LA BateriaInstrucciones de seguridad importantes­ ¡ADVERTENCIAAdvertencia Nota IV. MontajeColocación o extracción de la broca Instalación o desmontaje del cuboFuncionamiento del inter­ ruptor de rotación de avance FuncionamientoColocación y extracción de la batería Cuerpo principalSelección de modo de potencia de impacto Cómo utilizar el gancho del cinturónPara cambiar el lugar de ubicación del gancho de cinturón Panel de controleCuadro de guías de trabajo reco­ mendadas Luz LEDLuz de advertencia de sobrecalenta­ miento Vida útil de la batería Empuñadura recomendadaBloque de pilas Para un uso adecuado de la batería Batería de Li­iónPrecaución Cargador de la batería CargaFactores que afectan al par de apriete VI. MantenimientoVII. PAR DE Apriete Condiciones de apriete de pernos EY7546 M10 x 35 mm. M12, M14, M16 x 45 mm MPerno estándar kgf-cm Especificaciones VIII. AccesoriosIX. Anexo EY9L44 EY9L50 Tiempo de carga Cargador DE BateríaMemo Panasonic Consumer Electronics Company