Porter-Cable PCB575BG instruction manual Bench Grinder Safety

Page 5

BENCH GRINDER SAFETY

1.Wear eye protection that complies with ANSI Z87.1 specifications.

2.Use grinding wheels suitable for the speeds of the grinder.

3.Stand beside the bench grinder during start-up, not facing directly in front.

4.Do not remove the wheel guard.

5.Do not use the grinding wheel to cut anything.

6.Do not use anything to stress the grinding wheel.

7.Use a grinding wheel dressing tool to shape or remove glaze from grinding wheels.

8.Adjust distance between wheel and tool rest to maintain 1/8 inch (3.2 mm) or less separation as the diameter of the wheel decreases with use.

9.Connect to a supply circuit protected by a circuit breaker or time-delay fuse.

10.Secure the bench grinder to its supporting surface to prevent the grinder from tipping over, sliding, or walking on its supporting surface.

A.Replace a cracked wheel immediately.

B.Always use the guards and eye shields.

C.Do not overtighten the wheel nut.

D.Use only flanges furnished with this grinder.

11.Always inspect grinding wheels prior to use for cracks, missing pieces, etc. Replace wheel immediately before use.

12.USE ONLY GRINDING WHEELS that comply with ANSI B7.1 and rated greater than 3450 RPM.

13.GUARD AGAINST ELECTRICAL SHOCK by preventing body contact with grounded surfaces. For example: pipes, radiators, ranges, refrigerator enclosures.

14.DO NOT use wheels with incorrect size holes. NEVER use wheel washers or wheel screws that are defective or incorrect, and NEVER touch a grinding wheel or other moving parts.

15.NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the grinding path of the wheel.

16.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your hand to move into the wheel. ALWAYS make sure you have good balance.

17.NEVER stand or have any part of your body in line with the path of the wheel.

18.DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

19.DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY. This could cause the wheel to loosen and create a hazard. Should this ever occur, stand clear and allow the wheel to come to a complete stop. Disconnect your grinder from the power supply and retighten the wheel nut securely.

20.RISK OF INJURY DUE TO ACCIDENTAL STARTING. Do not use in an area where children may be present.

21.NEVER START THE GRINDER when the wheel is in contact with the workpiece.

22.SECURE WORK. Always hold the workpiece firmly against the work rest.

23.DO NOT USE THE BENCH GRINDER if the flange nut or clamp nut is missing or if the spindle shaft is bent.

24.FREQUENTLY clean grinding dust from beneath the grinder.

25.DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL OR ANY MEDICATION.

26.ALWAYS STAY ALERT. Do not allow familiarity (gained from frequent use of your grinder) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.

27.STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate the tool when you are tired. Do not rush.

28.SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct other users. If you loan someone this tool, loan them these instructions also.

29.ALWAYS EASE THE WORKPIECE AGAINST THE ABRASIVE WHEEL when starting to grind. A harsh impact can break the wheel. Use light pressure when starting to grind. Too much pressure on a cold wheel can cause the wheel to crack.

30.USE ONLY FLANGES furnished with this bench grinder.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Manuel d’instructions Manual de instrucciones California Proposition Table of ContentsSupport and Clamp Work Safety Guidelines DefinitionsProhibition General Safety Instructions Before Using this Power Tool Power Tool SafetyBench Grinder Safety Bench Grinder Safety Power Supply and Motor Specifications Electrical Requirements and SafetyGrounding Instructions Guidelines for Extension CordsTools Needed for Assembly Know Your Bench Grinder Installing Tool Rests FIG. A, B, C Assembly and AdjustmentsInstalling the Spark Guards FIG. D Installing the EYE Shields FIG. ENever USE a Grinding Wheel Without a Blotter Changing Grinding Wheels FIG. F, G, G-1, HReplacing the Bulb FIG Installing the Coolant Tray FIG. JAdjusting the Speed of Grinder FIG. O Using the Worklight FIG. NOperation Cooling Workpiece FIG. PScissors General OperationKnives ScrewdriversGeneral MaintenanceProblem Problem Cause Suggested Corrective Action Troubleshooting GuideReplacement Parts Service and Repairs Available Accessories Accessories and AttachmentsMM Variable Speed Grinder with Worklight Parts List Parts ListMM Variable Speed Grinder with Worklight Schematic Three Year Limited Warranty WarrantyAdvertencia Léase Este Moteur Meule Table DES MatièresProposition 65 DE LA Californie Mesures DE Sécurité Définitions Symboles D’AVERTISSEMENTInterdiction Soutenir ET Bien Serrer LES PiècesToujours Porter DES Lunettes DE Consignes DE Sécurité Outil ÉlectriqueNE PAS SE Pencher AU Dessus DE Sécurité Pour LA Meuleuse SUR Pied Boucliers Protecteurs ET Pareétincelles Caractéristiques Électriques ET SécuritéDonnées Techniques SUR LE Moteur ET L’ALIMENTATION Directives DE Mise À LA TerreCalibre Minimum DES Rallonges AWG Directives Concernant LES RallongesTableau DES Pièces Détachées ART Description Quantité Déballage DE LA Meuleuse SUR PiedDéballage ET Vérification DU Contenu Parties DE LA Meuleuse SUR Pied Installation DES Protecteurs Oculaires FIG. E Installation DES Appuis D’OUTIL FIG. A, B, CInstallation DES PARE-ÉTINCELLES FIG. D Remplacement DES Meules FIG. F, G, G-1, H Fig. J Installation DU BAC D’ARROSAGE FIG. JDémarrage ET Arrêt DE LA Meuleuse FIG. M UtilisationUtilisation DE LA Lampe DE Travail FIG. N Refroidissement DE LA Pièce FIG. PCiseaux FonctionnementCouteaux TournevisGénéralités EntretienGuide DE Dépannage Pièces DE Rechange Service APRÈS-VENTE ET RéparationsProblème Cause Probable Solution Conseillée Accessoires Offerts EN Option AccessoiresListe DE Pièces Liste DE PiècesX4BC SchémaRemarque Garantie Limitée DE Trois 3 ANS GarantieNúmero DE Catálogo PCB575BG Especificaciones DEL Producto ÍndiceProposicion 65 DE California Sección PáginaIconos DE Advertencia Pautas DE SEGURIDAD/DEFINICIONESProhibido Apoye LA Pieza DE Trabajo Y Asegurela CON AbrazaderasUtilice LOS Accesorios Recomendados Utilice Siempre Proteccion Para LOS OjosSeguridad EN EL Manejo DE Herramientas Eléctricas Seguridad EN EL Manejo DE LA Moledora DE Banco EN Caso DE QUE Alguna Pieza DE Requisitos Eléctricos Y DeseguridadEspecificaciones DEL Suministro Eléctrico Y DEL Motor Instrucciones Para LA Conexión a TierraCalibre Minimo Para Extensiones Electricas AWG Extensiones ElectricasTabla DE Piezas Sueltas Artículo Descripción Cantidad Desempaque DE LA Moledora DE BancoDesempaque Y Verificación DEL Contenido Protector contra las chispas Conozca SU Moledora DE BancoInstalacion DE LOS Soportes Para Herramientas FIG. A, B, C Ensamble Y AjustesInstalación DE LOS Protectores Contra Chispas FIG. D Instalación DE LOS Protectores Para LOS Ojos FIG. EFig. F Cambio DE LAS Muelas Abrasivas FIG. F, G, G-1, HInstalación DE LA Bandeja DE Refrigerante FIG. J Reemplazo DEL Foco FIGMontaje DE LA Herramienta Sobre UN Banco DE Trabajo FIG. K Almacenaje DE LA HerramientaComo Encender Y Apagar LA Moledora FIG. M FuncionamientoUSO DE LA LUZ DE Trabajo FIG. N Ajuste DE Lavelocidad DE Laamoladora FIG. OTijeras Trabajos GeneralesCuchillos DestornilladoresGenerales MantenimientoPiezas DE Repuesto Servicio Y Reparaciones Guia Para LA Solucion DE ProblemasProblema Causa DEL / Problema Acción Correctiva Sugerida Accesorios Disponibles Accesorios Y AcoplamientosLista DE Piezas Lista DE PiezasX4BC EsquemaNota Garantia Limitada POR Tres AÑO Garantía
Top Page Image Contents