Porter-Cable 1000003754 Service and Adjustments, To Drain Tank, To Replace or Clean Check Valve

Page 14

NOTE: See Operation section for the location of controls.

TO DRAIN TANK

Risk of Unsafe Operation. Risk from noise. Air tanks contain high pressure air. Keep face and other body parts away from outlet of drain. Use ANSI Z87.1 eye protection (CAN/CSA Z94.3) when draining as debris can be kicked up into face. Use ear protection [(ANSI S12.6 (S3.19) hearing protection] as air flow noise is loud when draining.

1.Set the On/Off switch to "Off".

2.Turn the regulator knob counter-clockwise to set the outlet pressure to zero.

3.Remove the air tool or accessory.

4.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 PSI. Release safety valve ring.

5.Drain water from air tank by opening drain valve on bottom of tank.

Risk of Bursting. Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

Risk of Property Damage. Drain water from air tank may con- tain oil and rust which can cause stains.

6.After the water has been drained, close the drain valve. The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, the reinstalled.

SERVICE AND ADJUSTMENTS

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.

Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor to cool.

TO REPLACE OR CLEAN CHECK VALVE

1. Release all air pressure from air tank. See "To Drain Tank" in the Maintenance section.

2. Unplug unit.

3.

Remove the hose by removing the

 

 

 

 

hose clamp. NOTE: The hose clamp

 

 

 

 

 

Hose Clamp

 

 

is not reusable. You must purchase a

 

 

 

 

 

 

 

 

 

 

 

new hose clamp, see the Parts List or

 

 

 

 

purchase a standard hose clamp at a

 

 

 

 

local hardware store.

Check Valve

4.

Unscrew the check valve (turn coun-

 

ter-clockwise) using a socket wrench.

 

 

 

5.Make sure the valve disc moves freely inside the check valve and the spring holds the disc in the upper, closed position. The check valve may be

cleaned with a solvent, such as paint and varnish remover.

6.Apply sealant to the check valve threads. Reinstall the check valve (turn clock-

1000003754

14 - ENG

Page 13 Page 15
Image 14
Page 13 Page 15
Contents C2005 What can Happen HOW to Prevent IT Safety Guidelines DefinitionsImportant Safety Instructions HazardRisk to Breathing Asphyxiation Attachments & accessories Risk of BurstingRisk from Flying Objects Risk of Electrical ShockElectrical Grounding Failure Risk of HOT Surfaces What can Happen HOW to Prevent IT Risk from Moving PartsRisk from Noise Risk of Unsafe Operation What can Happen HOW to Prevent ITRisk of Falling Glossary SpecificationsAccessories Duty CycleHOW to SET UP Your Unit AssemblyInstallation Grounding InstructionsExtension Cords Voltage and Circuit Protection Description of Operation Operation Know Your AIR Compressor Before Each Start-Up How to StopMotor Overload Protector not shown How to Start MaintenanceTo Check Safety Valve Customer ResponsibilitiesTo Drain Tank Service and AdjustmentsTo Replace or Clean Check Valve To Replace Regulator Service StorageTroubleshooting Problem Cause CorrectionProblem Cause Correction Problem Cause Correction Full ONE Year Warranty Incorrect USE can Cause HAZARDS. Follow These InstructionsÉvité, pourrait causer de graves Mesures DE Sécurité DéfinitionsConsignes DE Sécurité Importantes Blessures ou la mort Dommages à la propriétéRisque D’EXPLOSION OU D’INCENDIE Ce qui peut se produire Comment l’ÉviterRisque D’ÉCLATEMENT CE QUI Peut SE Produire Comment L’ÉVITERAccessoires PneusDirectives relatives à la mise à la Risque DE Choc ÉlectriqueMise à la terre électrique le fait de Risque Associé AUX Pièces MobilesRisque DE Chute Modèle no C2005 LexiqueRisque Associé AU Bruit Assemblage Cycle DE ServiceAccessoires Montage DE LappareilRallonges Protection Contre LA Surtension ET Protection DU CircuitDescription DU Fonctionnement UtilisationFAMILIARISEZ-VOUS Avec Votre Compresseur Dair Utilisation DE Lappareil Arrêt de lappareilAvant chaque mise en marche Mise en marcheVérification DE LA Soupape DE Sûreté EntretienResponsabilités DU Client Vidange DU RéservoirRemplacement OU Nettoyage DE LA Soupape DE Retenue Pour Remplacer LE Régulateu Entretien ET Réparation RangementPièces DE Rechange Dépannage Problème Cause CorrectionRemarque Ajustez Fusibles et remplacez-le Garantie Complète D’UN 1 AN Menores o moderadas Definiciones DE Normas DE SeguridadInstrucciones Importantes DE Seguridad Lesiones seriasPeligro Riesgo DE Explosión ¿QUÉ Puede SUCEDER? Cómo EvitarloElementos y accesorios NeumáticosRiesgo DE Objetos Despedidos Riesgo POR Piezas Móviles Riesgo DE Caídas ¿QUÉ Puede SUCEDER? Cómo Evitarlo Riesgo POR Ruidos ¿QUÉ Puede SUCEDER? Cómo EvitarloCiclo DE Servicio Cuadro DE EspecificacionesGlosario Modelo Nº C2005Desempaque EnsamblajeInstalación Ubicación DEL Compresor DE AireCables DE Extensión Eléctrica Protección DEL Voltaje Y DEL CircuitoDescripción DE Operaciones OperaciónConozca SU Compresor DE Aire Cómo Utilizar SU Unidad Cómo detenerlaAntes de cada puesta en marcha MantenimientoResponsabilidades DEL Cliente Cómo poner en marchaCómo Verificar LA Válvula DE Seguridad Cómo Drenar EL TanqueServicio Y Ajustes Para Reemplazar O Limpiar LA Válvula RetenciónPara Reemplazar EL Regulador Piezas DE Repuesto AlmacenajeServicio Mantenimiento Y ReparacionesAccesorios Guía DE Diagnóstico DE ProblemasProblema Causa CorrecciónUsando el accesorio El motor no funciona Fusible fundido inter Garantía Completa DE UN AÑO 1000003754 Deltaportercable.com
Top Page Image Contents