Delta 46-455, 46-460ST instruction manual Tailstock, Toolrest

Page 10

TAILSTOCK

To reduce the risk of injury, tighten all screws and levers securely when adjusting any part of the lathe.

ADJUSTING TAILSTOCK

To adjust the position of the tailstock (A), loosen tailstock locking lever (R) by lifting. Slide tailstock (A) along the bed (Fig. 11) into the desired location. Tighten tailstock locking lever (R) Fig. 10 by pressing downward to lock in place.

To reduce the risk of injury, don’t position edge of tailstock (S) Fig. 11 beyond the edge of the lathe bed (T).

REMOVING TAILSTOCK

To remove the tailstock (A) Fig. 10, unlock the tailstock locking lever (R) and slide it off the end of the lathe bed.

LOCKING THE QUILL

The quill locking screw (O) Fig. 12 locks the quill (Q) in place when used with the supplied live center or other lathe accessories.

TAILSTOCK CRANK

The tailstock crank (P) advances and retracts the quill (Q).

TOOLREST

To reduce the risk of injury, tighten all screws and levers securely when adjusting any part of the lathe.

To adjust the tool rest base (U) Fig. 13, loosen the tool rest base locking lever (V) and adjust. The tool rest base can be positioned side to side, forward and backwards or rotated as desired. Once in position, securely lock the base with the lever (V).

To adjust the tool rest (D), loosen the toolrest locking screw (W). The tool rest can be positioned as desired. Once in position, securely lock the tool rest with the lever

(V).

NOTE: if necessary, the spring-loaded locking screw handle (W) can be ratcheted to a more convenient position by pulling the handle outward.

R

A

Fig. 10

A

 

 

T

S

 

 

 

Fig. 11

Q

O

P

Fig. 12

D

W

V

U

Fig. 13

10

Image 10
Contents 46-455 46-460 Important Safety Instructions Table of ContentsSafety Guidelines Definitions General SAFETY RULES Properly Adjust the Tool Rest Height Additional Specific Safety RulesWhen Using the Included 3 76 MM Motor Specifications POWER CONNECTIONSGrounding Instructions Carton Contents Functional DescriptionAssembly Items Required AssemblyUnpacking and Cleaning Assembly Time EstimateRemoving Faceplate FaceplateReplacing Faceplate Removing the Spur Center Spur and Live CentersAttaching Spur Center Attaching Live CenterTailstock ToolrestChanging Lathe Speeds Speed Recommendations for Midi LatheElectronic Variable Speed Control 46-460 only Indexing PINSTARTING AND STOPPING LATHE LOCKING SWITCH in THE OFF POSITIONMotor Overload Protector Machine USE Turning in Reverse 46-460 only Troubleshooting MaintenanceKeep Machine Clean Failure to StartPeriodic Maintenance Belt ReplacementReplacement Parts Free Warning Label Replacement Service and RepairsAccessories Five Year Limited New Product WarrantyLES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsRègles DE Sécurité Générales Règles Spécifiques Additionnelles DE Sûreté Ajuster Correctement LA Hauteur DU PORTE- OutilSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Cordon DE Rallonge Description FonctionnelleContenus DE Boite AVANT-PROPOSDésemballage ET Nettoyage AssemblageFonctionnement Outils Nécessaires Pour L’ASSEMBLEEPlaque DE Montage Remplacement DE LA Plaque DE MontageRetrait DE LA Plaque DE Montage Retrait DE LA Pointe À Griffe Pointe À Griffe ET Pointe ’ENTRAÎNEMENTFixation DE LA Pointe À Griffe Fixation DE LA Pointe D’ENTRAÎNEMENTPORTE-OUTILS Poupée MobileChangement DE Régime DU Tour Recommandations DE Vitesses Pour LES Tours Midi Commande DE Vitesse Continue Électronique uniquement modèle Goupille D’INDEXATIONVerrouillage DU Commutateur EN Position D’ Arrêt « OFF » Mise EN Marche ET Arrêt DU TourProtecteur DE Surcharge DU Moteur Utilisation DE L’APPAREIL Montage DE LA PièceDepannage Tournage EN Marche Arrière uniquement modèleRemplacement DE LA Courroie Entretien RégulierService Pièces DE Rechange Remplacement Gratuit DE LétiquetteGarantie AccessoiriesEntretien ET Réparation Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNormas Generales DE Seguridad Normas Específicas Adicionales DE Seguridad GUARDE ESTAS INSTRUCCIONESESPECIFICACIONES DEL MOTOR Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Cordones DE Extensión Descripción FuncionalContenido DE Carton IntroducciónHerramientas DE Ensamblaje Requeridas OperaciónDesempaquetado Y Limpieza Estimación DEL Tiempo DE EnsamblajeExtracción DE LA Placa Frontal Placa FrontalCentro Giratorio Y Centro DE Dientes Rectos Reemplazo DE LA Placa FrontalColocación DEL Centro Giratorio Colocación DEL Centro DE Dientes RectosExtracción DEL Centro DE Dientes Rectos Extracción DEL Centro GiratorioSoporte DE LA Herramienta Cabezal MóvilCambio DE LAS Velocidades DEL Torno Velocidades Recomendadas Para EL Torno Mediano Control Electrónico DE Velocidad Variable 46-460 Únicamente Clavija IndicadoraBloqueo DEL Interruptor EN LA Posición DE Apagado OFF Encendido Y Apagado DEL TORNOProtector DE Sobrecarga DEL Motor Utilizar LA Maquina Montaje DE LA Pieza DE TrabajoTorneado EN Reversa 46- 460 Únicamente Mantenga LA Máquina LimpiaMantenimiento Periódico Cambio DE LA CorreaPage Servicio AccesoriosIdentificación Delproducto Póliza DE GarantíaExcepciones Garantia Garantía limitada de cinco años para productos nuevosPage Delta Power Equipment Corporation