DeWalt DWS520SK, DWS520K instruction manual Plunge Cuts

Page 13

CAUTION: Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated AC only on DC current. To do so may seriously damage the tool.

1.Place the machine with the front part of the saw base on the workpiece.

2.Press the on/off switch to turn the saw on.

3.Push the plunge trigger (A) forward, press the saw down to set cutting depth and push it forward into cutting direction.

Push the saw forward at a speed which allows the blade to cut without laboring. Hardness and toughness can vary even in the same piece of material, and knotty or damp sections can put a heavy load on the saw. When this happens, push the saw more slowly, but hard enough to keep it working without much decrease in speed. Forcing the saw can cause rough cuts, inaccuracy, kickback and over-heating of the motor.

Should the cut begin to go off the line, DO NOT try to force it back. Release the switch and allow blade to come to a complete stop, then withdraw the saw, realign, and start a new cut slightly inside the wrong one.

In any event, withdraw the saw if you must shift the cut. Forcing a correction inside the cut can stall the saw and lead to kickback. IF SAW STALLS, RELEASE THE TRIGGER, ALLOW THE BLADE TO COME TO A COMPLETE STOP, AND BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE CUT AND CLEAR OF THE CUTTING EDGE BEFORE RESTARTING.

As you finish a cut, release the trigger and allow the blade to stop before lifting the saw from the work. As you lift the saw, the spring- tensioned guard will automatically close

around the blade. Remember the blade is exposed until this occurs, never reach under the work for any reason whatsoever.

Always use a track, fence or straight edge guide when ripping.

11

NOTE: When cutting thin strips, be careful to ensure that the narrow strips do not feed up into the inside of the blade enclosure. NOTE: The tracks, available in different lengths, allow for precise, clean cuts and simultaneously protect the workpiece surface against damage.

FIG. 8

T

W

Y

AA

T

PLUNGE CUTS (FIG. 1, 8)

WARNING: ALWAYS use the track when plunge cutting. WARNING: To avoid kickbacks, the following instructions MUST

be observed when plunge cutting:

English

Image 13
Contents DWS520 Page General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetyService Causes and Operator Prevention of Kickback Additional Safety Instructions for Saws Safety Instructions for Plunge-Type SawsMinimum Gauge for Cord Sets Extension CordsComponents -3 MotorBevel Adjustment Fig Adjustments and SET-UPIntended USE Cutting Depth Adjustment Fig Adjusting the Riving Knife FigOperation Changing the Saw Blade Fig Switching On and Off FigWorkpiece Support Wrong CuttingPlunge Cuts Ripping CROSS-CUTTINGBevel Cutting Lifting the SAW When Making Bevel CUT Improper Depth of CUT Setting on SAWKickback Improper Workpiece SupportTrack Saw System Fig BladesAnti-splinter Strip Blade SelectionMaintenance Speed Adjustment FigCleaning Wall Cutting FigThree Year Limited Warranty Accessories RepairsLubrication BrushesDAY Money Back Guarantee Year Free ServiceSécurité DU Lieu DE Travail Définitions lignes directrices en matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Utilisation ET Entretien D’UN Outil Électrique Sécurité PersonnelleConsignes de sécurité propres à toutes les scies Règles DE Sécurité Particulières AdditionnellesRéparation Causes ET Préventions DES Rebonds Consignes de sécurité additionnelles propres aux scies Calibres Minimaux DES Rallonges RallongesMoteur Conserver CES ConsignesUsage Prévu Description à 3Réglage du couteau diviseur Fig Réglages ET ConfigurationRéglage de chanfrein Fig Mise en marche et arrêt de l’appareil FonctionnementRéglage de profondeur de coupe Fig Changement de lame àSupport de pièce Coupe Coupes EN Plongée Coupes Longitudinales Coupes TransversalesCoupes EN Biseau Rebonds Configuration DE Profondeur DE Coupe IncorrecteSupport DE Pièce Inadéquat Torsion DE LA Lame Mésalignement DE CoupeDispositif de rail de scie Fig LamesSélection DE LA Lame Réglage de la vitesse Fig Bande anti-éclatsCoupe d’un mur Fig Types DE Matériau À Couper Plages DE VitessesEntretien Dépoussiérage FigLubrification Balais de moteurRéparations AccessoiresGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANGarantie DE Remboursement DE 90 Jours Seguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalInstrucciones de Seguridad para Todas las Sierras Reglas Específicas DE Seguridad AdicionalesMantenimiento Causas Y Prevención DEL Rebote POR EL Operador Instrucciones de Seguridad Adicionales para Sierras Instrucciones de Seguridad para las Sierras Tipo- InmersiónCalibre Mínimo Para Juegos DE Cables AlargadoresGuarde Estas Instrucciones Componentes -3 Ajuste de Bisel Fig Ajuste Y ConfiguraciónAjuste de la Navaja Separadora Fig Intención DE USOOperación Ajuste de la Profundidad de Corte FigEncendido y Apagar Fig Cambiar la Hoja de la Sierra FigSoporte de la Pieza de Trabajo Cortar Cortes DE Inmersión Rasgar Corte -TRANSVERSALRebote Cortar BiselSoporte Inapropiado DE LA Pieza DE Trabajo Ajuste Inadecuado DE LA Profundidad DE Corte EN LA SierraHojas Cinta Anti-astillas Sistema de la Sierra de Incisión FigAjuste de Velocidad Fig Tipo DE Material Rango DE SER Cortado VelocidadExtracción de Polvo Fig Cortes en Pared FigMantenimiento LimpiezaEscobillas LubricaciónAccesorios ReparacionesExcepciones Póliza de GarantíaAÑO DE Servicio Gratuito Garantía limitada por tres añosGarantía DE Reembolso DE SU Dinero POR 90 Días EspecificacionesHerramientas Electricas Page