DeWalt DWS520K, DWS520SK instruction manual Cross-Cutting, Ripping, Bevel Cutting

Page 14

English

1.Place the machine onto the track and release the anti-kickback knob (U) by turning it counterclockwise.

2.Turn the machine on and slowly press the saw down onto the set cutting depth and push forward in the cutting direction. The cut indicators (T) display the absolute front and the absolute rear cutting points of the saw blade [dia. 6-1/2" (165 mm)] at maximum cutting depth and using the track.

3.If kickback happened during the plunge cut, turn the anti- kickback knob (U) counterclockwise to release it from the track.

4.When you have finished the plunge cut, turn the anti-kickback knob (U) clockwise into the lock position.

CROSS-CUTTING

Cutting directly across the grain of a piece of lumber is called crosscutting. Figures 9 and 10 illustrate a crosscut operation. Position the work so that the cut will be on the left.

FIG. 9

FIG. 10

RIPPING

Ripping is cutting wood lengthwise. This operation is performed in the same manner as crosscutting with the exception of supporting the workpiece. If the workpiece is supported on a large table, bench, or floor, several pieces of scrap stock approximately 1" (25.4 mm) thick should be placed beneath the material to allow clearance for the portion of the saw blade that extends thru the workpiece. Large sheets of paneling or thin plywood supported on saw horses should have 2 x 4’s placed lengthwise between the horses and the workpiece to prevent it from sagging in the center.

BEVEL CUTTING

Make your bevel cuts in the same manner as crosscuts and rip cuts, but set the blade at an angle between 0° and 47°.

The bevel cut made at an angle to the edge of a board is called a compound cut.

12

Image 14
Contents DWS520 Page Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyService Personal SafetyPower Tool USE and Care Causes and Operator Prevention of Kickback Safety Instructions for Plunge-Type Saws Additional Safety Instructions for SawsExtension Cords Minimum Gauge for Cord SetsMotor Components -3Intended USE Adjustments and SET-UPBevel Adjustment Fig Operation Adjusting the Riving Knife FigCutting Depth Adjustment Fig Workpiece Support Switching On and Off FigChanging the Saw Blade Fig Cutting WrongPlunge Cuts Bevel Cutting CROSS-CUTTINGRipping Kickback Improper Depth of CUT Setting on SAWLifting the SAW When Making Bevel CUT Improper Workpiece SupportAnti-splinter Strip BladesTrack Saw System Fig Blade SelectionCleaning Speed Adjustment FigMaintenance Wall Cutting FigLubrication Accessories RepairsThree Year Limited Warranty BrushesYear Free Service DAY Money Back GuaranteeSécurité EN Matière D’ÉLECTRICITÉ Définitions lignes directrices en matière de sécuritéSécurité DU Lieu DE Travail Sécurité Personnelle Utilisation ET Entretien D’UN Outil ÉlectriqueRéparation Règles DE Sécurité Particulières AdditionnellesConsignes de sécurité propres à toutes les scies Causes ET Préventions DES Rebonds Consignes de sécurité additionnelles propres aux scies Rallonges Calibres Minimaux DES RallongesConserver CES Consignes MoteurDescription à 3 Usage PrévuRéglage de chanfrein Fig Réglages ET ConfigurationRéglage du couteau diviseur Fig Réglage de profondeur de coupe Fig FonctionnementMise en marche et arrêt de l’appareil Changement de lame àSupport de pièce Coupe Coupes EN Plongée Coupes EN Biseau Coupes TransversalesCoupes Longitudinales Support DE Pièce Inadéquat Configuration DE Profondeur DE Coupe IncorrecteRebonds Torsion DE LA Lame Mésalignement DE CoupeSélection DE LA Lame LamesDispositif de rail de scie Fig Coupe d’un mur Fig Bande anti-éclatsRéglage de la vitesse Fig Types DE Matériau À Couper Plages DE VitessesLubrification Dépoussiérage FigEntretien Balais de moteurGarantie limitée de trois ans AccessoiresRéparations Contrat D’ENTRETIEN Gratuit D’UN ANGarantie DE Remboursement DE 90 Jours Seguridad Eléctrica Definiciones Normas de seguridadSeguridad EN EL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaMantenimiento Reglas Específicas DE Seguridad AdicionalesInstrucciones de Seguridad para Todas las Sierras Causas Y Prevención DEL Rebote POR EL Operador Instrucciones de Seguridad para las Sierras Tipo- Inmersión Instrucciones de Seguridad Adicionales para SierrasAlargadores Calibre Mínimo Para Juegos DE CablesGuarde Estas Instrucciones Componentes -3 Ajuste de la Navaja Separadora Fig Ajuste Y ConfiguraciónAjuste de Bisel Fig Intención DE USOEncendido y Apagar Fig Ajuste de la Profundidad de Corte FigOperación Cambiar la Hoja de la Sierra FigSoporte de la Pieza de Trabajo Cortar Cortes DE Inmersión Corte -TRANSVERSAL RasgarSoporte Inapropiado DE LA Pieza DE Trabajo Cortar BiselRebote Ajuste Inadecuado DE LA Profundidad DE Corte EN LA SierraHojas Ajuste de Velocidad Fig Sistema de la Sierra de Incisión FigCinta Anti-astillas Tipo DE Material Rango DE SER Cortado VelocidadMantenimiento Cortes en Pared FigExtracción de Polvo Fig LimpiezaAccesorios LubricaciónEscobillas ReparacionesPóliza de Garantía ExcepcionesGarantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosAÑO DE Servicio Gratuito EspecificacionesHerramientas Electricas Page