Black & Decker BDPS600K, BDPS400K instruction manual Developing the Proper Sprayingtechnique

Page 11

If you are using the direct to can hose, you will need to prime the sprayer by removing air from the system. Toprime:

1. Make sure the sprayer is plugged in, and turn the flow control knob counterclockwise to maximum (figure K).

2. Hold the sprayer below the level of the paint. This will speed up the priming (figure L).

3. Aim the sprayer at a piece of scrap wood or cardboard. Squeeze the trigger and hold until all air is out of the system and material is flowing freely out of the sprayer tip. This could take up to three minutes.

Important: The end of the direct to can hose must remain completely submerged in the material. If it is not completely submerged and air is sucked into the system, the piston could seize. If the piston seizes, the sound the sprayer makes will change to a low hum and the sprayer will quickly become hot to the touch. Never run the sprayer when the piston is seized. Should this happen, clean the piston and the pump housing thoroughly using the cleanup procedures found in this manual.

K

L

DEVELOPING THE PROPER SPRAYINGTECHNIQUE

• Practice spraying on a piece of scrap material such as cardboard to test your spray pattern and become familiar with
the speed settings flow control features of the sprayer.
• Ensure surface to be sprayed is free of dust, dirt, and grease.
• Ensure spray area is clean and free of dust that could be blown onto newly sprayed surfaces.
• Cover any areas not intended to be sprayed.
• Always spray from a minimum of 1 inch (25mm) to a maximum of 14 inches (355mm) (figure M). Optimal is usually
around 10 inches or use a paint stir stick as a reference.
• A commonly used method for spraying a large surface is the “crisscross” pattern. This is done by spraying in horizon-
tal strips and then crossing over these strips with vertical strips.
• To get an even spray distribution, always keep your arm at the same distance (figure M) from the surface you are
spraying and avoid moving your wrist (figure M1).	11

Image 11

Contents Power Paint Sprayer On/Off Switch Priming With Remote Tubing To avoid these risks, take the following preventions Safety Guidelines DefinitionsImportant Safety Instructions To avoid these risks,GENERALtake the. following preventions General Safety WarningsGrounding Instructions Volts Extension CordsComponents CleaningpinAttachingthe Spraynozzles Figures Adjusting the FAN Spraynozzle Figures D and D1SET-UP Selecting the Proper Spray Nozzle Figures B and B1Filling the Canister Figure F Common Dilution Rates on Paint canLiquid Material Preparation Figures , E1 Preparation TipsSubmerged in the material container Aligning the Pickup TubePickup tube can be aligned Push the suction hose onto the intake Return ports as shownOperation Speed and Flow Control SettingsSpraying and avoid moving your wrist figure M1 Developing the Proper SprayingtechniqueUsing the Quick Clean System CleaningTo Begin Cleaning HOW to USE the Quick Clean SystemUnplug the sprayer from the power source Cleaning the Direct to can Hose Slide the spring onto the front of the piston ReassemblyProblem Possible Cause Possible Solution TroubleshootingService Information MaintenanceAccessories Mode DʼEMPLOI Table DES Matières Lignes directrices en matière de sécurité définitionsDʼemploi Consignes DE Sécurité ImportantesRisque Risque dʼexplosionInstructions DE Mise À LA Terre Avertissements DE Sécurité GénérauxRallonges Une mauvaise installation de la ficheComposants Fixation DES Buses DE Pulvérisation Figures C ET C1 PréparationChoix DE LA Buse DE Pulvérisation Adéquate Figures B ET B1 Conseils DE Préparation Taux DE Dilution Courants Indiqués SUR LE Contenant DEPeinture Préparation DU Produit Liquide Figur S E ET E1Alignement DU Tube DʼASPIRATION SeulementDétente MARCHE/ARRÊT Figure J Réglages DE Vitesse ET DE DébithFonctionnement J Bouton DE Réglage DE Débit FigureLA Matière Pulvérisée DE LA Matière Pulvérisée Mettre AU Point UNE Bonne Technique DE PUL RisationAP Plicat Ionun Iforme DE Application IrrégulièreUtilisation DU Circuit DE Nettoyage Rapide NettoyageGouttes, passer un coup de pinceau sec pour les lisser Horaire figure N3Pour Amorcer LE Nettoyage Comment Utiliser LE Circuit DE Nettoyage RapideNettoyage DU Flexible Relié Directement AU Contenant Avant figure R1 RéassemblageGlisser le ressort sur la partie avant du piston Insérer le piston et le ressort dans le boîtierDépannage Problème Cause possible Solution possibleInformation SUR LES Réparations AccessoiresEntretien Manual DE Instrucciones Interruptor de encendido/apagado Cebado con tubo remoto Estos peligros, tome las precauciones siguientes InstruccionesInstrucciones DE Conexión a Tierra Advertencias DE Seguridad GeneralLa capacidad adecuada Cables ProlongadoresNo utilice un adaptador con este producto BDPS600 únicamente Aguja de limpieza Descripción DE LAS FuncionesAjuste DE LA Boquilla DE Pulverización Tipo Abanico InstalaciónSelección DE LA Boquilla DE Pulverización Adecuada Llenado DEL Depósito Figura F Proporciones Comunes DE Dilución EN Latas DE PinturaPreparación DE Materiales Líquidos Figuras E Y E1 Consejos DE PreparaciónEl tubo de recogida y el filtro Alineación DEL Tubo DE RecogidaEn forma recta, ubique el tubo de recogida Cebado CON LA Manguera Directo a LA Lata BDPS600 Únicamente FuncionamientoPerilla DE Control DE Flujo Figura Gatillo DE ENCENDIDO/APAGADO Figura JLimpieza indicados en este manual Desarrollo DE LA Técnica DE Pulverización AdecuadaCebado Figura L Patrón de pulverización LimpiezaGoteos, tenga a mano una brocha seca para emparejarlos USO DEL Sistema DE Limpieza RápidaPara Iniciar LA Limpieza Cómo Utilizar EL Sistema DE Limpieza RápidaDesenchufe el pulverizador de la fuente de alimentación Seque bien todas las piezasLimpieza DE LA Manguera Directo a LA Lata Figura R5 Émbolo Figura RSolamente para Propósitos de México Detección DE ProblemasProblema Causa posible Solución posible Solamente Para Propositos DE Mexico Información DE MantenimientoBosques DE Cidros Acceso Radiatasno Años DE GarantiaEsta Garantia no Aplica Cuando Black & Decker S.A. DE C.V