Hitachi B 16RM instruction manual On / OFF Switch Panel Fig. S, Laser ON/OFF Switch Fig. Q-1

Page 16

English

ON / OFF SWITCH PANEL (Fig. S)

The “ON / OFF” switch has a removable, yellow plastic key. With the key removed from the switch, unauthorized and hazardous use by children and others is minimized.

1.To turn the drill press “ON”, insert the key (2) into the slot of the switch (1), and move the switch upward to the “ON” position.

2.To turn the drill press “OFF”, move the switch downward.

3.To lock the switch in the “OFF” position, grasp the yellow key of the toggle switch and pull it out.

4.With the switch key removed, the switch will not operate to power the drill press on.

5.If the switch key is removed while the drill press is running, it can be turned “OFF” but cannot be restarted without inserting the switch key.

6.To turn the worklight “ON”, press the rocker switch (3) to the on position.

7.Never leave the drill press unattended. Turn the light switch and power switch “OFF” and wait until it comes to a complete stop, and remove the safety key to prevent unauthorized starts.

Fig. S

LIGHTMAX

LUMIERELAMP AMPOULE

80W

MAX

3

2

1

WARNING

ALWAYS lock the switch “OFF” when the drill press is not in use. Remove the key and keep it in a safe place. In the event of a power failure, blown fuse, or tripped circuit breaker, turn the switch “OFF” and remove the key, preventing an accidental startup when power comes on.

WARNING

Laser is radiated when laser guide is turned on. Avoid direct eye exposure. Always un-plug drill pres from power source before making any adjustment.

LASER ON/OFF SWITCH (Fig. Q-1)

To turn the laser On or Off, press the rocker switch (3).

INSTALLING A DRILL BIT IN THE CHUCK (Fig. T)

1.With the switch “OFF” and the yellow switch key removed, open the chuck jaws (1) using the chuck key

(2). Turn the chuck key counterclockwise to open the chuck jaws (1).

2.Insert the drill bit (3) into the chuck far enough to obtain maximum gripping by the jaws, but not far enough to touch the spiral grooves (flutes) of the drill bit when the jaws are tightened.

3.Make sure that the drill is centered in the chuck.

4.Turn the chuck key clockwise to tighten the jaws.

WARNING

To avoid injury or accident by the chuck key ejecting forcibly from the chuck when the power is turned “ON”, use only the self-ejecting chuck key supplied with this drill press. ALWAYS recheck and remove the chuck key before turning the power “ON”.

Fig. T

2

1

3

WARNING

To prevent the workpiece or backup material from being torn from your hands while drilling, you MUST position the workpiece against the LEFT side of the column. If the workpiece or the backup material is not long enough to reach the column, clamp them to the table, or use the fence provided with the drill press to brace the workpiece. Failure to secure the workpiece could result in personal injury.

— 16 —

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 16RM Hitachi Authorized Service Centers Product Specifications EnglishGeneral Safety Instructions SafetyBefore Using this Drill Press Specific Safety Instructions for the Drill Press Grounding Instructions Guidelines for Extension CordsAccessories and Attachments Carton ContentsEfgh Mnopq Know Your Drill Press Glossary of Terms Assembly and Adjustments Assembly InstructionsEstimated Assembly Times 20~40 Minutes Tools NeededInstalling Feed Handles Fig. E Installing the Head Fig. DInstalling the Chuck Fig. G, H Installing Light Bulb Fig. J not included Drill Press AdjustmentsBevel Scale Fig. L Quill Return Spring Fig. O Spindle / Quill Fig. NBelt Tension Fig. P Operations Basic Drill Press OperationsLaser Guide Avoid Direct EYE ContactLaser ON/OFF Switch Fig. Q-1 On / OFF Switch Panel Fig. SInstalling a Drill BIT in the Chuck Fig. T Drilling to a Specific Depth Fig Workpiece methodDepth scale method Removing Chuck and Arbor FigBasic Operation Instructions Your ProtectionDrill Bit Material Diam Wood Alumi Mild Stain Inches Num SteelTilting the Table Fig. AA Positioning the Table and Workpiece Fig. Y and ZFeeding Maintaining Your Drill Press MaintenanceLubrication Troubleshooting Guide TroubleshootingProblem Possible Causes Remedy Caracteristiques DU Produit Consignes Generales DE Securite SecuriteAvant Toute Utilisation DE Cette Perceuse a Colonne Consignes DE Securite Specifiques a LA Perceuse a Colonne Consignes Relatives AUX Rallonges Instructions DE Mise a LA MasseVeillez à ce que le cordon de rallonge soit correctement Accessoires Accessoires RecommandesContenu DE L’EMBALLAGE Deballage ET Verification DU ContenuEfgh Mnopq Connaitre Votre Perceuse a Colonne Glossaire Boutons DE Blocage DE LA Tension DES CourroiesEcrous DE Blocage DE L’ECHELLE DE Profondeur Interrupteur MARCHE/ARRET DE LA PerceuseMontage ET Reglage Instructions DE MontageTemps D’ASSEMBLAGE Estime a 20~40 Minutes Outils NecessairesInstallation DES Poignees D’ABAISSEMENT Fig. E Reglage DE LA Perceuse a Colonne Installation DE L’AMPOULE Fig. J non fournieEchelle D’INCLINAISON Fig. L Ressort DE Retour DU Fourreau Fig. O Broche / Fourreau Fig. NTension DES Courroies Fig. P LE Laser -GUIDE Evitez Tout Contact Direct Avec LES YeuxFonctionnement Utilisation DES Fonctions DE Base DE LA Perceuse a ColonnePercer a UNE Profondeur Secifique Fig Méthode de la pièce à usinerMéthode de l’échelle de profondeur Blocage DU Mandrin a UNE Profondeur Definie Fig. WPour Votre Protection Instructions DES Operations DE BaseEnlever LE Mandrin ET L’ARBRE Fig Acier Pouces Doux Diamètre Matériau Du foret BoisInclinaison DE LA Table Fig. AA Entretien Entretenir Votre Perceuse a ColonneAlimentation LubrificationGuide DE Resolution DES Pannes Resolution DES PannesProbleme Causes Possibles Solution Especificaciones DEL Producto Instrucciones Generales DE Seguridad SeguridadAntes DE Utilizar Esta Taladradora Instrucciones DE Seguridad Específicas Para LA Taladradora Indicaciones Para LOS Cables Instrucciones DE Conexión a TierraProlongadores Accesorios Contenido DE LA CajaAccesorios Recomendados Desembalaje Y Comprobación DEL ContenidoEfgh Mnopq Conozca SU Taladradora Tuercas DE Parada DE LA Escala DE Profundidad Glosario DE TérminosSumidero Roscado 5/8 Coloque una tubería Montaje Y Ajustes Instrucciones DE MontajeTiempo DE Montaje Estimado 20-40 Minutos Herramientas NecesariasInstalación DEL Portabrocas Fig. G, H e Instalación DEL Cabezal Fig. DInstalación DE LOS Mangos DE Alimentación Fig. E Instalación DE LA Bombilla Fig. J no se incluye Ajustes DE LA TaladradoraEscala DE Bisel Fig. L Resorte DE Vuelta DEL Manguito Fig. O EJE / Manguito Fig. NTensión DE LA Cinta Fig. P Funciones Funciones Básicas DE LA TaladradoraEL Laser -GUIDE Evite EL Contacto Ocular DirectoInterruptor ON/OFF DEL Láser Fig. Q-1 Panel DE Interruptor on / OFF Fig. SInstalación DE LAS Brocas EN EL Portabrocas Fig. T Bloqueo DEL Portabrocas a LA Profundidad Deseada Fig. W Método de escala de profundidadExtracción DEL Portabrocas Y DEL Árbol Fig Instrucciones Básicas DE Fundionamiento SU ProtecciónInclinación DE LA Mesa Fig. AA Coloque LA Mesa Y LA Pieza DE Trabajo Fig. Y y ZAlimentación Mantenimiento DE LA Taladradora MantenimientoLubricación Guía DE Solución DE Problemas Solución DE ProblemasProblema Causas Posibles Solución Parts List Drill Press Model NO. B16RM Page Page Hitachi Koki Canada Co
Top Page Image Contents