Hitachi B 16RM Positioning the Table and Workpiece Fig. Y and Z, Tilting the Table Fig. AA

Page 19

POSITIONING THE TABLE AND WORKPIECE (Fig. Y and Z)

1.Lock the table (1) to the column (2) at a position so the tip of the drill bit (3) is just above the top of the workpiece (4).

2.ALWAYS place BACK-UP MATERIAL (scrap wood) on the table beneath the workpiece. This will prevent splintering or heavy burring on the underside of the workpiece. To keep the back-up material from spinning out of control, it MUST contact the LEFT side of the column.

WARNING

To prevent the workpiece or backup material from being torn from your hands while drilling, you MUST position it against the LEFT side of the column. If the workpiece or the backup material is not long enough to reach the column, use the fence provided with the drill press to brace the workpiece. Failure to do this could result in personal injury.

Fig. Y

2

3

4

1

3.For small pieces that cannot be clamped to the table, use a drill press vise (optional accessory).

WARNING

The drill press vise MUST be clamped or bolted to the table to avoid injury from a spinning workpiece, or damaged vise or bit parts.

Remove the drill press fence when it interferes with other drill press accessories.

Fig. Z

English

TILTING THE TABLE (Fig. AA)

NOTE: The table arm and support (1) has a predrilled hole with a locking set screw inserted for locking the table into a predetermined 0° horizontal position.

1.TIGHTEN the nut (4) on the locking pin in the clockwise direction to RELEASE the pin from the table support.

2.LOOSEN the large hex head bevel locking bolt (3).

WARNING

To prevent injury, be sure to hold the table & table arm assembly, so it will not swivel or tilt.

Fig. AA

1

3

2

4

1.Tilt the table, aligning the desired angle measurement to the zero line opposite the scale (4). Tighten the bevel locking bolt.

2.To return the table to its original position, loosen the bevel locking bolt (3). Realign the bevel scale (4) to the 0° position.

3.Loosen the nut (2) on the locking pin to the end of the pin. Gently tap the locking pin until it is seated in the mating hole on the table bracket. Tighten the bevel locking nut against the bracket to hold position.

WARNING

To avoid injury from spinning work or tool breakage, always clamp workpiece and backup material securely to the table before operating the drill press with the table tilted.

FEEDING

1.Pull down the feed handles with only enough effort to allow the drill bit to cut.

2.Feeding too slowly might cause the drill bit to burn. Feeding too rapidly might stop the motor, cause the belt or drill to slip, or tear the workpiece loose and break the drill bit.

3.When drilling metal, it may be necessary to lubricate the drill bit tip with motor oil, to prevent burning.

— 19 —

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 16RM Hitachi Authorized Service Centers English Product SpecificationsGeneral Safety Instructions SafetyBefore Using this Drill Press Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Grounding InstructionsCarton Contents Accessories and AttachmentsEfgh Mnopq Know Your Drill Press Glossary of Terms Tools Needed Assembly and AdjustmentsAssembly Instructions Estimated Assembly Times 20~40 MinutesInstalling Feed Handles Fig. E Installing the Head Fig. DInstalling the Chuck Fig. G, H Installing Light Bulb Fig. J not included Drill Press AdjustmentsBevel Scale Fig. L Quill Return Spring Fig. O Spindle / Quill Fig. NBelt Tension Fig. P Avoid Direct EYE Contact OperationsBasic Drill Press Operations Laser GuideLaser ON/OFF Switch Fig. Q-1 On / OFF Switch Panel Fig. SInstalling a Drill BIT in the Chuck Fig. T Removing Chuck and Arbor Fig Drilling to a Specific Depth FigWorkpiece method Depth scale methodMild Stain Inches Num Steel Basic Operation InstructionsYour Protection Drill Bit Material Diam Wood AlumiTilting the Table Fig. AA Positioning the Table and Workpiece Fig. Y and ZFeeding Maintaining Your Drill Press MaintenanceLubrication Troubleshooting Guide TroubleshootingProblem Possible Causes Remedy Caracteristiques DU Produit Consignes Generales DE Securite SecuriteAvant Toute Utilisation DE Cette Perceuse a Colonne Consignes DE Securite Specifiques a LA Perceuse a Colonne Consignes Relatives AUX Rallonges Instructions DE Mise a LA MasseVeillez à ce que le cordon de rallonge soit correctement Deballage ET Verification DU Contenu AccessoiresAccessoires Recommandes Contenu DE L’EMBALLAGEEfgh Mnopq Connaitre Votre Perceuse a Colonne Interrupteur MARCHE/ARRET DE LA Perceuse GlossaireBoutons DE Blocage DE LA Tension DES Courroies Ecrous DE Blocage DE L’ECHELLE DE ProfondeurOutils Necessaires Montage ET ReglageInstructions DE Montage Temps D’ASSEMBLAGE Estime a 20~40 MinutesInstallation DES Poignees D’ABAISSEMENT Fig. E Reglage DE LA Perceuse a Colonne Installation DE L’AMPOULE Fig. J non fournieEchelle D’INCLINAISON Fig. L Ressort DE Retour DU Fourreau Fig. O Broche / Fourreau Fig. NTension DES Courroies Fig. P Evitez Tout Contact Direct Avec LES Yeux LE Laser -GUIDEUtilisation DES Fonctions DE Base DE LA Perceuse a Colonne FonctionnementBlocage DU Mandrin a UNE Profondeur Definie Fig. W Percer a UNE Profondeur Secifique FigMéthode de la pièce à usiner Méthode de l’échelle de profondeurPour Votre Protection Instructions DES Operations DE BaseEnlever LE Mandrin ET L’ARBRE Fig Acier Pouces Doux Diamètre Matériau Du foret BoisInclinaison DE LA Table Fig. AA Lubrification EntretienEntretenir Votre Perceuse a Colonne AlimentationGuide DE Resolution DES Pannes Resolution DES PannesProbleme Causes Possibles Solution Especificaciones DEL Producto Instrucciones Generales DE Seguridad SeguridadAntes DE Utilizar Esta Taladradora Instrucciones DE Seguridad Específicas Para LA Taladradora Indicaciones Para LOS Cables Instrucciones DE Conexión a TierraProlongadores Desembalaje Y Comprobación DEL Contenido AccesoriosContenido DE LA Caja Accesorios RecomendadosEfgh Mnopq Conozca SU Taladradora Tuercas DE Parada DE LA Escala DE Profundidad Glosario DE TérminosSumidero Roscado 5/8 Coloque una tubería Herramientas Necesarias Montaje Y AjustesInstrucciones DE Montaje Tiempo DE Montaje Estimado 20-40 MinutosInstalación DEL Portabrocas Fig. G, H e Instalación DEL Cabezal Fig. DInstalación DE LOS Mangos DE Alimentación Fig. E Instalación DE LA Bombilla Fig. J no se incluye Ajustes DE LA TaladradoraEscala DE Bisel Fig. L Resorte DE Vuelta DEL Manguito Fig. O EJE / Manguito Fig. NTensión DE LA Cinta Fig. P Evite EL Contacto Ocular Directo FuncionesFunciones Básicas DE LA Taladradora EL Laser -GUIDEInterruptor ON/OFF DEL Láser Fig. Q-1 Panel DE Interruptor on / OFF Fig. SInstalación DE LAS Brocas EN EL Portabrocas Fig. T Bloqueo DEL Portabrocas a LA Profundidad Deseada Fig. W Método de escala de profundidadExtracción DEL Portabrocas Y DEL Árbol Fig SU Protección Instrucciones Básicas DE FundionamientoInclinación DE LA Mesa Fig. AA Coloque LA Mesa Y LA Pieza DE Trabajo Fig. Y y ZAlimentación Mantenimiento DE LA Taladradora MantenimientoLubricación Guía DE Solución DE Problemas Solución DE ProblemasProblema Causas Posibles Solución Parts List Drill Press Model NO. B16RM Page Page Hitachi Koki Canada Co
Top Page Image Contents