Hitachi B 16RM instruction manual Product Specifications, English

Page 3

English

WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints

•Crystalline silica from bricks, cement and other masonry products

•Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

PRODUCT SPECIFICATIONS

Chuck Size	5/8"
Speed	12 (250 ~ 3,100 min–1)
Motor	120V, 60 Hz, 8 Amps
Horsepower	1 HP (Max. Developed)
Built-in Light	60 Watt (Maximum)
	(Bulb not included)
Table Size	13-15/64" x 13-15/64"
Table Tilt	45° Right or Left
Spindle Travel	3-1/8"
Throat	7-1/2"
Base Size	11" x 20-3/8"
Height	63-1/4"
NET WEIGHT	156.5 LB (71.0 kg)

WARNING

To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection.

Your drill press is wired at the factory for 120V operation. Connect to a 120V, 15 AMP branch circuit and use a 15 AMP time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

— 3 —

Image 3

Contents 16RM Hitachi Authorized Service Centers English Product SpecificationsSafety General Safety InstructionsBefore Using this Drill Press Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Grounding InstructionsCarton Contents Accessories and AttachmentsEfgh Mnopq Know Your Drill Press Glossary of Terms Tools Needed Assembly and AdjustmentsAssembly Instructions Estimated Assembly Times 20~40 MinutesInstalling the Head Fig. D Installing Feed Handles Fig. EInstalling the Chuck Fig. G, H Drill Press Adjustments Installing Light Bulb Fig. J not includedBevel Scale Fig. L Spindle / Quill Fig. N Quill Return Spring Fig. OBelt Tension Fig. P Avoid Direct EYE Contact OperationsBasic Drill Press Operations Laser GuideOn / OFF Switch Panel Fig. S Laser ON/OFF Switch Fig. Q-1Installing a Drill BIT in the Chuck Fig. T Removing Chuck and Arbor Fig Drilling to a Specific Depth FigWorkpiece method Depth scale methodMild Stain Inches Num Steel Basic Operation InstructionsYour Protection Drill Bit Material Diam Wood AlumiPositioning the Table and Workpiece Fig. Y and Z Tilting the Table Fig. AAFeeding Maintenance Maintaining Your Drill PressLubrication Troubleshooting Troubleshooting GuideProblem Possible Causes Remedy Caracteristiques DU Produit Securite Consignes Generales DE SecuriteAvant Toute Utilisation DE Cette Perceuse a Colonne Consignes DE Securite Specifiques a LA Perceuse a Colonne Instructions DE Mise a LA Masse Consignes Relatives AUX RallongesVeillez à ce que le cordon de rallonge soit correctement Deballage ET Verification DU Contenu AccessoiresAccessoires Recommandes Contenu DE L’EMBALLAGEEfgh Mnopq Connaitre Votre Perceuse a Colonne Interrupteur MARCHE/ARRET DE LA Perceuse GlossaireBoutons DE Blocage DE LA Tension DES Courroies Ecrous DE Blocage DE L’ECHELLE DE ProfondeurOutils Necessaires Montage ET ReglageInstructions DE Montage Temps D’ASSEMBLAGE Estime a 20~40 MinutesInstallation DES Poignees D’ABAISSEMENT Fig. E Installation DE L’AMPOULE Fig. J non fournie Reglage DE LA Perceuse a ColonneEchelle D’INCLINAISON Fig. L Broche / Fourreau Fig. N Ressort DE Retour DU Fourreau Fig. OTension DES Courroies Fig. P Evitez Tout Contact Direct Avec LES Yeux LE Laser -GUIDEUtilisation DES Fonctions DE Base DE LA Perceuse a Colonne FonctionnementBlocage DU Mandrin a UNE Profondeur Definie Fig. W Percer a UNE Profondeur Secifique FigMéthode de la pièce à usiner Méthode de l’échelle de profondeurInstructions DES Operations DE Base Pour Votre ProtectionEnlever LE Mandrin ET L’ARBRE Fig Diamètre Matériau Du foret Bois Acier Pouces DouxInclinaison DE LA Table Fig. AA Lubrification EntretienEntretenir Votre Perceuse a Colonne AlimentationResolution DES Pannes Guide DE Resolution DES PannesProbleme Causes Possibles Solution Especificaciones DEL Producto Seguridad Instrucciones Generales DE SeguridadAntes DE Utilizar Esta Taladradora Instrucciones DE Seguridad Específicas Para LA Taladradora Instrucciones DE Conexión a Tierra Indicaciones Para LOS CablesProlongadores Desembalaje Y Comprobación DEL Contenido AccesoriosContenido DE LA Caja Accesorios RecomendadosEfgh Mnopq Conozca SU Taladradora Glosario DE Términos Tuercas DE Parada DE LA Escala DE ProfundidadSumidero Roscado 5/8 Coloque una tubería Herramientas Necesarias Montaje Y AjustesInstrucciones DE Montaje Tiempo DE Montaje Estimado 20-40 MinutosInstalación DEL Cabezal Fig. D Instalación DEL Portabrocas Fig. G, H eInstalación DE LOS Mangos DE Alimentación Fig. E Ajustes DE LA Taladradora Instalación DE LA Bombilla Fig. J no se incluyeEscala DE Bisel Fig. L EJE / Manguito Fig. N Resorte DE Vuelta DEL Manguito Fig. OTensión DE LA Cinta Fig. P Evite EL Contacto Ocular Directo FuncionesFunciones Básicas DE LA Taladradora EL Laser -GUIDEPanel DE Interruptor on / OFF Fig. S Interruptor ON/OFF DEL Láser Fig. Q-1Instalación DE LAS Brocas EN EL Portabrocas Fig. T Método de escala de profundidad Bloqueo DEL Portabrocas a LA Profundidad Deseada Fig. WExtracción DEL Portabrocas Y DEL Árbol Fig SU Protección Instrucciones Básicas DE FundionamientoColoque LA Mesa Y LA Pieza DE Trabajo Fig. Y y Z Inclinación DE LA Mesa Fig. AAAlimentación Mantenimiento Mantenimiento DE LA TaladradoraLubricación Solución DE Problemas Guía DE Solución DE ProblemasProblema Causas Posibles Solución Parts List Drill Press Model NO. B16RM Page Page Hitachi Koki Canada Co