Panasonic EY7840 Battery Pack For Appropriate Use of Bat- tery pack, Li-ion Battery pack EY9L40

Page 10

(2) Overheat warning lamp

Off

Flashing: Overheat

(normal

Indicates operation has

operation)

been halted due to battery

 

overheating.

The overheating protection feature halts tool operation to protect the battery pack in the event of over- heating. The overheat warning lamp on the control panel flashes when this feature is active.

If the overheating protection feature activates, allow the tool to cool thoroughly (at least 30 minutes). The driver is ready for use when the overheat warning lamp goes out.

Avoid using the tool in a way that causes the overheating protection feature to activate repeatedly.

(3)Battery low warning lamp

Installing the Shoulder Strap

CAUTION:

Install the shoulder strap firmly to the main unit of the tool and check the length of the strap before use.

Check the condition of the strap and do not use if it is cut or torn etc.

There is a risk of injury or damage if used while improperly installed.

Please wear the shoulder strap se- curely on the shoulder.

There is a risk of injury or damage if it is accidentally dropped.

1.Pass the strap through the strap holders. ()

2.Pass the strap through the buckles and adjust the length. ()

Off

Flashing

(normal

(No charge)

operation)

Battery protection

 

feature active

The battery protection feature acti- vates immediately before the battery loses its charge, causing the battery low warning lamp to flash.

If you notice the battery low warning lamp flashing, charge the battery pack immediately.

Shoulder pad

The shoulder strap can be adjusted according to the individual.

Adjust the shoulder pad to the shoulder.

Pull the shoulder strap to make sure it is firmly attached to the main unit of the tool.

[Battery Pack]

For Appropriate Use of Bat- tery pack

Li-ion Battery pack (EY9L40)

For optimum battery life, store the Li- ion battery pack following use without charging it.

When charging the battery pack, con- firm that the terminals on the bat- tery charger are free of foreign sub-

- 10 -

Image 10
Contents Model No EY7840 ImportanteIndex/Index/Indice English Français Español PáginaAdaptateur de mèche EY9HX403E Adaptador de broca EY9HX403E Personal Safety Work Area SafetyElectrical Safety IntroductionService Power Tool Use and CareBattery Tool Use and Care Specific Safe TY RulesImportant Safety Instructions For BatterySymbol Meaning Do not attempt to disassemble the battery pack housing To insert the bit AssemblyBit adapter To remove the bitControl Panel Clutch Torque SettingOperation Forward/Reverse LeverLi-ion Battery pack EY9L40 Battery Pack For Appropriate Use of Bat- tery packInstalling the Shoulder Strap Battery low warning lampBattery Recycling Battery Charger ChargingBattery Pack Life Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery PackNi-MH/Ni-Cd Battery Pack During charging, the charging lamp will be litLamp Indications Accessories MaintenanceUsage Suggestion Specifications Set according to the work environment of the siteLi-ion battery pack Battery ChargerNi-Cd/Ni-MH battery pack Sécurité personnelle Consignes DE Securite GENE- RalesSécurité électrique AVERTISSEMENT! Veuillez lireMaintenez les outils de coupe af- fûtés et propres Utilisation et soins de l’outil mécaniqueLes outils de coupe bien entrete Utilisation et soins de la batterie de l’outil Regles DE Securite PAR- TiculieresRéparation Chargeurdebat Symbole SignificationInstructions de sécurité impor- tantes Norme d’entrée Ampères Mise EN Garde UtilisationPour insérer la mèche Adaptateur de mèche FonctionnementFixation ou retrait de la bat- terie autonome Levier d’inversion marche avant-marche arrièreCommutateur martelage/ perforation Panneau de commandeGâchette de commande de vitesse Ajustement du couple d’em- brayageBatterie autonome Li-ion EY9L40 Installation de la dragonneBatterie Témoin d’avertissement de sur- chauffeRecyclage de la batterie auto- nome BatteryChargeur de batterie Recharge Batterie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Complètement la batterie avant son utilisationEntretien Indication DU VoyantAccessoires Suggestion Pour L’UTILISATIONCaracteristiques Techniques Réglez conformément à l’environnement du lieu de travailBatterie autonome Li-ion Chargeur DE BatterieBatterie autonome Ni-MH/Ni-Cd Seguridad eléctrica IntroducciónDAD Generales Seguridad personalEn manos de usuarios no entrenados Uso y cuidados de her- ramientas eléctricasUso y cuidado de la her- ramienta a batería Mantenga las herramientas de corte afiladas y limpiasMente y la unidad puede dañarse DAD EspecíficasServicio Símbolo SignificadoPara EL Carga Instrucciones de seguridad im- portantesNo incinere la batería. Puede explo- tar en el fuego MontajePuede deteriorar la batería guardada PrecauciónPalanca de avance/inversión FuncionamientoAdaptador de broca Para desmontar la brocaDisparador del control de velocided variable Palanca de conmutación de martillo/taladroAjuste del par del embrague Luz LEDLuz de advertencia de sobrecalenta- miento Instalación de la correa al hombroLuz de advertencia de batería baja Atención Para batería Li-ión, EY9L40Nota Batería de Li-iónBatería Ni-MH/Ni-Cd Enchufe el cargador en la fuente de alimentación de CAMantenimiento Para la limpiezaAccesorios Sugerencias Para EL USOEspecificaciones Unidad PrincipalBatería Memo Memo Panasonic Consumer Electronics Company