Panasonic EY7840 Battery Charger Charging, Battery Pack Life, Battery Recycling

Page 11

stances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign sub- stances are found on the terminals.

The life of the battery pack terminals may be affected by foreign substances such as dust and water etc. during operation.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals togeth- er may cause sparks, burns or a fire.

When operating the battery pack, make sure the work place is well ven- tilated.

When the battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to prevent dust or dirt from con- taminating the battery terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a limited life. If the operation time be- comes extremely short after recharg- ing, replace the battery pack with a new one.

Battery Recycling

ATTENTION:

FOR Li-ion Battery Pack, EY9L40

A Li-ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERYfor information on how to recycle this battery.

[Battery Charger]

Charging

Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack

The ambient temperature range is be- tween 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the battery temperature is below 0°C (32°F), the tool may fail to function properly.

Use the charger at temperatures be- tween 0°C and 40°C, and charge the battery at a temperature similar to that of the battery itself. (There should be no more than a 15°C difference be- tween the temperatures of the battery and the charging location.)

When charging a cool battery pack (below 0°C (32°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature.

Cool down the charger when charging more than two battery packs consecu- tively.

Do not insert your fingers into contact hole, when holding charger or any other occasions.

CAUTION:

To prevent the risk of fire or damage to the battery charger.

Do not use power source from an engine generator.

Do not cover vent holes on the charger and the battery pack.

Unplug the charger when not in use.

Li-ion Battery Pack

NOTE:

Your battery pack is not fully charg- ed at the time of purchase. Be sure to charge the battery before use.

- 11 -

Image 11
Contents Importante Model No EY7840English Français Español Página Index/Index/IndiceAdaptateur de mèche EY9HX403E Adaptador de broca EY9HX403E Introduction Work Area SafetyElectrical Safety Personal SafetySpecific Safe TY Rules Power Tool Use and CareBattery Tool Use and Care ServiceSymbol Meaning For BatteryImportant Safety Instructions Do not attempt to disassemble the battery pack housing To remove the bit AssemblyBit adapter To insert the bitForward/Reverse Lever Clutch Torque SettingOperation Control PanelBattery low warning lamp Battery Pack For Appropriate Use of Bat- tery packInstalling the Shoulder Strap Li-ion Battery pack EY9L40Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack Battery Charger ChargingBattery Pack Life Battery RecyclingDuring charging, the charging lamp will be lit Ni-MH/Ni-Cd Battery PackLamp Indications Usage Suggestion MaintenanceAccessories Set according to the work environment of the site SpecificationsNi-Cd/Ni-MH battery pack Battery ChargerLi-ion battery pack AVERTISSEMENT! Veuillez lire Consignes DE Securite GENE- RalesSécurité électrique Sécurité personnelleLes outils de coupe bien entrete Utilisation et soins de l’outil mécaniqueMaintenez les outils de coupe af- fûtés et propres Réparation Regles DE Securite PAR- TiculieresUtilisation et soins de la batterie de l’outil Instructions de sécurité impor- tantes Symbole SignificationChargeurdebat Norme d’entrée Ampères Pour insérer la mèche UtilisationMise EN Garde Levier d’inversion marche avant-marche arrière FonctionnementFixation ou retrait de la bat- terie autonome Adaptateur de mècheAjustement du couple d’em- brayage Panneau de commandeGâchette de commande de vitesse Commutateur martelage/ perforationTémoin d’avertissement de sur- chauffe Installation de la dragonneBatterie Batterie autonome Li-ion EY9L40Batterie autonome Li-ion BatteryChargeur de batterie Recharge Recyclage de la batterie auto- nomeComplètement la batterie avant son utilisation Batterie autonome Ni-MH/Ni-CdIndication DU Voyant EntretienSuggestion Pour L’UTILISATION AccessoiresRéglez conformément à l’environnement du lieu de travail Caracteristiques TechniquesBatterie autonome Ni-MH/Ni-Cd Chargeur DE BatterieBatterie autonome Li-ion Seguridad personal IntroducciónDAD Generales Seguridad eléctricaMantenga las herramientas de corte afiladas y limpias Uso y cuidados de her- ramientas eléctricasUso y cuidado de la her- ramienta a batería En manos de usuarios no entrenadosSímbolo Significado DAD EspecíficasServicio Mente y la unidad puede dañarseInstrucciones de seguridad im- portantes Para EL CargaPrecaución MontajePuede deteriorar la batería guardada No incinere la batería. Puede explo- tar en el fuegoPara desmontar la broca FuncionamientoAdaptador de broca Palanca de avance/inversiónLuz LED Palanca de conmutación de martillo/taladroAjuste del par del embrague Disparador del control de velocided variableLuz de advertencia de batería baja Instalación de la correa al hombroLuz de advertencia de sobrecalenta- miento Para batería Li-ión, EY9L40 AtenciónEnchufe el cargador en la fuente de alimentación de CA Batería de Li-iónBatería Ni-MH/Ni-Cd NotaPara la limpieza MantenimientoSugerencias Para EL USO AccesoriosUnidad Principal EspecificacionesBatería Memo Memo Panasonic Consumer Electronics Company