ICP-CC404 Installation Guide 6.0 System Functions
To set the first Test Report:
1.Enter the Installer Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the number of days (1 to 15) until the first Test Report is sent and press [AWAY].
Two beeps sound and the STAY and AWAY indicators turn off. The system returns to the disarmed state.
Each time you enter Installer’s Programming Mode, the first Test Report time defaults to the repeat interval set in Location 366.
The number of days counts down by one at 2400 hours as set in Locations 901 to 904 (refer to Section 17.15 System Time on page 72).
Example
If the repeat interval is set to 7 days, but you want the first Test Report to be sent in 2 days, enter:
[1 2 3 4 1][AWAY][2][AWAY]
6.1.2Changing Domestic Phone Numbers
When the system is set up for domestic dialing, this function allows the installer to view and program the telephone numbers that the system calls if an alarm occurs. Refer to Section 9.0 Domestic Dialing on page 40 for more information.
To change domestic phone numbers:
1.Enter the Installer Code and press [2][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
If there are telephone numbers programmed, they appear one digit at a time using the remote codepad indicators. Refer to Table 21 on page 28 for the indicators and their meanings.
If there are no telephone numbers programmed, an additional two beeps sound after entering this mode. These two beeps normally sound after you enter the last digit of the last phone number.
2.Enter the first phone number. Each digit appears as you enter it.
3.If you are programming another phone number, press [STAY][4] to separate the end of one phone number and the beginning of the next.
If you are not programming other numbers, go to Step 5.
4.Repeat Steps 2 and 3 to program another phone number.
5.Press [AWAY] to exit from this mode.
Table 20: Domestic Dialing Digits
|
|
|
|
Digit | Number to | Digit | Number to |
Required | Program | Required | Program |
0 | 0 | 8 | 8 |
1 | 1 | 9 | 9 |
2 | 2 | 10 | refer to 0 |
3 | 3 | * | * 1 |
4 | 4 | # | * 2 |
5 | 5 | 4 sec pause | * 3 |
6 | 6 | break | * 4 |
7 | 7 | 15 | * 5 |
Example
If you want to program two separate telephone numbers (9672 1777 and 9672 1233), enter:
[1 2 3 4 2][AWAY][9 6 7 2 1 7 7 7][STAY] [4 9 6 7 2 1 2 3 3][AWAY]
You can suspend domestic dialing at any time (for example, you are moving house and do not want the system to continue calling your work place or mobile phone).
To disable domestic dialing:
Enter the Installer Code and press [2][AWAY] [STAY][4][AWAY].
Table 21: Codepad Indicators When Changing Phone Numbers
|
|
| Zone Indicators |
|
| MAINS | |||
Digit | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Indicator |
0 |
|
|
|
|
|
|
|
| X |
|
|
|
|
|
|
|
|
|
|
1X
2
X
3 | X |
4
X
5 | X |
6
X
7 | X |
8
X
9 | X |
| X | ||||
11 | X |
|
|
|
|
| X |
12 |
| X |
|
| X | ||
Pause |
|
| X |
|
|
| X |
Break |
|
|
| X |
|
| X |
15 |
|
|
|
| X |
| X |
6.1.3Change Telco Arming or Disarming Sequence
Program the call forward sequence to automatically operate when you arm the system in AWAY Mode. This feature is only available if the call forward option is available from your telecommunication provider.
28 | Bosch Security Systems, Inc. 12/08 |