User Code Priority | Bosch Appliances ICP-CC404 specification

ICP-CC404 Installation Guide 13.0 Access Code

User Codes are four digits long. The fifth position specifies the priority level for the code. Each User Code has its own priority level. More than one User Code can have the same priority level. The priority level controls the behaviour of the code, such as allowing it to arm only, to arm and disarm, or allow access to the Master Code functions (refer to Section 13.3 User Code Priority on page 52). The installer can assign access to Master Code functions to multiple User Codes.

Only the installer can change the priority level.

The ICP-CC404 Control Panel can have up to eight programmable User Codes (1 to 8) to operate the system. Refer to Section 4.0 System Operations on page 18 for information about the different methods to arm and disarm the system.

Although 16 User Codes are available, User Codes 9 through 16 can only be Remote Radio User Codes. User Codes 9 to 16 allow systems that require remote radio control by hand-held remote transmitters. Refer to Section 5.0 Remote Radio Transmitter Operations on page 24 for information on remote operations and adding and deleting Remote Radio User Codes.

User Code 16 is reported when any of these methods is used to arm or disarm the system:

•Arming and disarming using remote radio control equipment connected to the RE005E 2-Channel Radio Interface.

•Arming and disarming using the CC816 Alarm Link Software.

•Arming remotely by telephone.

•Single button arming in AWAY Mode, STAY Mode 1, or STAY Mode 2.

•Single button disarming from STAY Mode 1 or STAY Mode 2.

•Automatic arming in AWAY Mode or STAY Mode 1.

•Automatic disarming from AWAY Mode, STAY Mode 1, or STAY Mode 2

Table 41: Priority Levels


Level	Description

0	Arm or disarm
1	Arm only
2	Arm or disarm and Open or Close Reports
3	Arm only and Close Report
4	Arm or disarm and code to isolate
6	Arm or disarm, code to isolate, and Open or
	Close Reports

8	Arm or disarm and Master Code functions
10	Arm or disarm, Master Code functions, and
	Open or Close Reports
12	Arm or disarm, Master Code functions, and code
	to isolate
14	Arm or disarm, Master Code functions, code to
	isolate, and Open or Close Reports

Arm/Disarm

The user can arm and disarm the system. A Closing Report is sent only after a previous code that can send an Opening Report disarms the system.

Arm Only

The user can arm the system but cannot disarm the system. A Closing Report is sent only after a previous code that can send an Opening Report disarms the system.

Open/Close Reports

Open and Close reports are sent to the monitoring station when the user disarms and arms the system, but only if Open/Close Reports is enabled in Locations 333 and 334 (refer to Section 15.6 Open/Close Reports on page 61).

Code To Isolate

If one or more User Codes has this option included, the method of standard isolating is disabled and only a User Code with this option in its priority level can isolate zones before arming the system using the Code to Isolate method. Refer to Section 4.11 Isolating Zones on page 21 for more information.

13.3User Code Priority

The installer can assign one of ten different priority levels to a User Code. Each priority level allows or restricts a user from performing specific functions.

When priority level 4, 6, 12, or 14 is assigned to any User Codes, the Standard Isolating method no longer operates. Only User Codes with a priority level of 4, 6, 12, or 14 can isolate zones using the Code to Isolate method.

Master Code Functions

The user has access to all Master Code functions. Refer to Section 6.2 Master Code Functions on page 31 for more information.

52	Bosch Security Systems, Inc. 12/08 F01U089401-02