Bosch Appliances ICP-CC404 manual Hold Down Function

ICP-CC404 Installation Guide Index

Handover		54	Codepad Panic Alarm		65
Hold Down Function			Codepad Tamper		66
Arm In STAY Mode 1		37	Communications Failure		67
Arm In STAY Mode 2		37	Communications Failure After 3 Unsuccessful Calls .67
Bell Test		37	Day Alarm Enabled		65
Initiate Modem Call		38	Day Alarm Latching		65
Reset Latching Outputs		38	Day Alarm Resetting		65
Send Test Report		38	Dialer Active		67
Strobe Test		37	Dialer Disabled		67
Turning Day Alarm On/Off		38	EDMSAT - Satellite Siren		64
Installer Code		50	Entry Warning		64
Installer Code Function			Entry Warning + Day Alarm Resetting		64
Change Telco Arm/Disarm Sequence		28, 34	Exit Warning		64
Setting STAY Mode 2 Zones		30, 35	Exit Warning Finished		64
Telephone Monitor Mode		30	Exit Warning With All Zones Sealed Or Entry
Installer's Programming Commands			Warning		64
958 - Enable/Disable Zone Status		11	Fire Alarm Latching		66
959 - Test Programming Key		11	Fire Alarm Resetting		66
960 - Exit Installer's Programming Mode		12	Fire Alarm Verification		66
961 - Reset Control Panel Back To Factory Default . 12			Global Chime		67
965 - Set Up Domestic Dialing		13	Horn Speaker		66
966 - Automatic Stepping Of Locations		13	Horn Speaker Monitor Fail		65
999 - Display Panel Type/Software Version Number14			Kiss-Off After Exit Time		64
Introduction		7	Kiss-Off Received		65
Invalid Code		73	Low Battery		65
Isolate In STAY Mode 1		57	Mimic System Fault		66
Isolating Allowed		57	Mimic Zone 1		67
Isolating Zones		21	Mimic Zone 2		67
Latching Outputs			Mimic Zone 3		67
Resetting		38	Mimic Zone 4		67
Lockout Dialer		56	Mimic Zone 6		67
Lockout Siren		56	Mimic Zone 7		67
Low Battery		22	Mimic Zone 8		67
MAINS Indicator		16, 17, 18	Radio Control Output 1		67
Master Code Function			Radio Control Output 1 - Not In AWAY Mode		67
Changing & Deleting User Codes		32	Radio Control Output 2		67
Setting Date and Time		36	Radio Control Output 2 - Not In AWAY Mode		67
Turning Outputs ON/OFF		36	Remote Control 1		66
Walk Test Mode		36	Remote Control 2		66
Medical Alarm		21	Remote Control 3		66
Modem Call		38	Ring Detect		67
New Zealand Telepermit Notes		83	Sensor Watch Alarm		65
Night Arm Station		76	Silent Alarm		66
Off Indicator		18	Sirens Running		66
On Indicator		18	Strobe Operating		66
Option Bits	10, 40, 49, 52, 56, 57		System Armed		64
Optional Equipment			System Disarmed		64
2-Channel Radio Interface		75	Telephone Line Fail		65
8 Zone LED Codepad		76	Zone Not Sealed		67
Night Arm Station		76	Zone Not Sealed After Exit Time		67
Programming Key		76	Outputs
PS100 Power Supply		76	One Shot Polarities		69
TF008 Plug Pack		76	Pulsing Polarities		69
Output Event Type			Redirecting Output To Codepad Buzzer		64
AC Fail		65	Turning On/Off		36
AC Mains 60 Hz or 50 Hz		67	Panic Alarm		21
Alarm When In AWAY Mode		66	Power Up Disarmed		73
Alarm When In STAY Mode		66	Primary Telephone Number For Receiver 1		45
Armed In AWAY Mode		64	Programming		9
Armed In STAY Mode		64	Automatic Stepping Of Locations		13
Auto Arm Pre-Alert Time		64	Entry/Exit Tiemrs		69
AUX Power Supply Fail		65	Option Bits	10, 40, 49, 52, 56, 57
Codepad Duress Alarm		66	Via Programming Key		10
Codepad Fire Alarm		65	Via Remote Codepad		9
Codepad Medical Alarm		65	Programming Key		10, 76

96 Bosch Security Systems, Inc. 12/08 F01U089401-02