| 2.0 | Programming |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Table 6: | Command 965 Defaults |
|
|
|
| ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
| Location |
| Description |
| Default Value | Setting |
| |
|
|
|
|
|
|
| ||
| 032 |
| Handshake Tone for Receiver 1 | 1 | (Handshake Tone) |
| ||
| 033 |
| Transmission Format |
| 4 | (Domestic) |
| |
|
|
|
|
|
|
|
| |
| 034 to 039 |
| Subscriber ID Number |
| 0, 0, 0, 0, 0, 1 | (1 Beep) |
| |
| 332 |
| Zone Status Reporting Options | 2 | (Receiver 2 only) |
| ||
| 333 and 334 |
| Open/Close Reports |
| 11, 12 | (Open/Close Reports) |
| |
| 335 |
| Open/Close Reporting Options | 2 | (Receiver 2 only) |
| ||
|
|
|
|
|
|
| ||
| 356 to 358 |
| System Status – Access Denied | 6, 7, 12 | (Access Denied) |
| ||
| 359 |
| System Status Reporting Options | 2 | (Receiver 2 only) |
| ||
| 360 to 366 |
| Test Report Time |
| 0, 0, 0, 0, 7, 1, 0 | (Test Reports) |
| |
| 367 |
| Test Reporting Dialer Options | 1 | (Receiver 1 only) |
| ||
Example (Auto Step Mode Enabled)
To enter the Primary Telephone Number 02 (pause)
9672 1055 when Auto Step Mode is enabled:
1.Press [0 #].
You are positioned at Location 000 (the Primary Telephone Number for Receiver 1).
2.To program the number, press:
[10 * 2 * 13 * 9 * 6 * 7 * 2 * 1 * 10 * 5 * 5 * 0*]
Example (Auto Step Mode Disabled)
To enter the Primary Telephone Number 02 (pause)
9672 1055 when Auto Step Mode is disabled:
1.Press [0 #].
You are positioned at Location 000 (the Primary Telephone Number for Receiver 1).
2.To program the number, press:
[10 * # 2 * # 13 * # 9 * # 6 * # 7 * # 2 * # 1 * # 10 * # 5 * # 5 * # 0 *]
2.4.10Command 999 – Display the Panel Type or Software Version Number
When using the remote codepad, this command shows the version of the control panel. Because different control panels use the same printed circuit board (PCB), it is difficult to determine the control panel the PCB is set to.
To show the control panel type or software version number:
1.Enter the Installer Code (the default is 1234) and press [#] to enter Installer’s Programming Mode. Two beeps sound and the remote codepad shows the data programmed in Location 000.
If you are using the remote codepad, the STAY and AWAY indicators flash to indicate you entered Installer’s Programming Mode.
2.Enter [9 9 9 #]. Two beeps sound.
If you are using the remote codepad, the codepad displays a zone indicator corresponding to the control panel type. Refer to Table 7 for more information.
Table 7: Control Panel Type
Indicator | Control Panel Type |
4
8ICP-CC408
3.Press [#] to exit from this command and return to the Installer’s Programming Mode.
4.Enter [9 6 0 #] to exit from the Installer's Programming Mode.
Two sound and the system returns to the disarmed state.
If you are using the remote codepad, the STAY and AWAY indicators turn off to indicate the system is disarmed.
14 | Bosch Security Systems, Inc. 12/08 |