Location 332 (Section 15.5 Zone Status Reporting Options on page 61) is ignored when programming the Alarm Restore code and is global for all zones. A zone Restore Report is sent only to the receiving party to which the zone is allocated (for example, Receiver 1 or Receiver 2).
15.5Zone Status Reporting Options
Use Location 332 to select whether Zone Status Reports are sent to Receiver 1 (the default), Receiver 2, or both, Receiver 2 only when Receiver 1 fails, or there is no reporting at all. Table 46 lists the reporting options.
Table 46: Zone Status Reporting Options
Option Description
0No report required
1 | Receiver 1 |
2 | Receiver 2 |
4Receiver 1 and Receiver 2
8Receiver 2 only when Receiver 1 fails
15.6Open/Close Reports
Program the Open Report value in Location 333 (the default value is 11) and the Close Report value in Location 334 (default 12).
An Opening Report (Contact ID Event Code 401) is sent to the base station receiver when the system is disarmed from AWAY Mode. A Closing Report (Contact ID Event Code 401) is sent at the end of Exit Time when the system is armed in AWAY Mode.
If an expanded format is selected, this code is used as the Expansion Code and the user number that armed or disarmed the system follows in the same transmission.
To enable Open and Close Reports in STAY Mode, select Option 2 in Location 178 (refer to Section 12.2 Dialer Options 2 on page 50). To enable Open and Close Reports only after a previous alarm, select Option 1 in Location 178.
If Open and Close Reports are not required, program Locations 333 and 334 as 0.
15.7Open/Close Reporting Options
Use Location 335 to select whether Zone Status Reports are sent to Receiver 1 (the default), Receiver 2, or both, Receiver 2 only when Receiver 1 fails, or there is no reporting at all. Table 47 lists the reporting options.
Table 47: Open/Close Reporting Options
Option Description
0No Open/Close Reports required
1 | Receiver 1 |
2 | Receiver 2 |
4Receiver 1 and Receiver 2
8Receiver 2 only when Receiver 1 fails
15.8Codepad Duress Report
Program the Codepad Duress Report value in Location 336.
The default value is 6.
A Duress Report (Contact ID Event Code 121) is sent to the base station receiver when a user adds 9 to the end of any valid User Code used to disarm the system. This alarm is always silent. A Duress Alarm can be activated during Exit Time (in other words, if the system is armed and then disarmed with a 9 at the end of the User Code before Exit Time expires, a Duress Report is sent). Adding 9 to the end of a User Code when arming the system does not cause a Duress Alarm.
If you want a 3 to activate a Codepad Duress Alarm instead of 9, select Option 2 in Location 430 (refer to Section 18.7 Consumer Options 3 on page 75).
Restore Reports are not sent for this event.
If Duress Reports are not required, program Location 336 as 0.
15.9Codepad Panic Report
Program the Codepad Panic Report value in Location 337 (tens digit) and Location 338 (units digit).
The default values are 7 (tens) and 15 (units).
A Panic Alarm Report (Contact ID Event Code 120) is sent to the base station receiver when a user presses either [1] and [3] or [STAY] and [AWAY] at the same time. A Panic Alarm is audible, but you can program the alarm as silent by selecting Option 1 in Location 425 (refer to Section 18.2 System Options 2 on page 73).
Restore Reports are not sent for this event.
If Panic Reports are not required, program Locations 337 and 338 as 0.
15.10 Codepad Fire Report
Program the Codepad Fire Report value in Location 339 (tens digit) and Location 340 (units digit).
The default values are 7 (tens) and 14 (units).
Bosch Security Systems, Inc. 12/08 | 61 |