Bosch Appliances ICP-CC404 Zone Programming Defaults, Zone Types Instant Zone, Handover Zone

ICP-CC404 Installation Guide 14.0 Zone Information

The Zone Report Code determines whether the control panel sends Alarm Reports for the zone. Refer to Section 14.3.7 Zone Report Code on page 59 for more information.

The Zone Dialer Options location enables you to specify how a zone sends a report to a base station receiver. Refer to Section 14.3.8 Zone Dialer Options on page 59 for more information.

Zone Defaults

The default zone parameters for the ICP-CC404 Control Panel are listed in Table 43. You can program Zones 1 to 4 as any Zone Type, but you can only program Zones 5 to 8 as a 24-Hour Zone Type.

Table 43: Zone Programming Defaults

Zone	Default		Zone	Pulse	Pulse	Zone	Zone	Report	Dialer
Number	Type	Locations	Type	Count	Time	Options 1	Options 2	Code	Options
Zone 1	Delay 1	267 to 273	2	0	0	1	14	1	1
Zone 2	Handover	274 to 280	1	0	0	1	14	1	1
Zone 3	Handover	281 to 287	1	0	0	1	14	1	1
Zone 4	Instant	288 to 294	0	0	0	1	14	1	1
Zone 5	Fixed 24-hr burglary	295 to 301	12	0	0	1	12	1	1
Zone 6	Fixed 24-hr burglary	302 to 308	12	0	0	1	12	1	1
Zone 7	Fixed 24-hr fire	309 to 315	13	0	0	1	12	1	1
Zone 8	Fixed 24-hr tamper	316 to 322	9	0	0	1	12	1	1

14.3.1Zone Types

0 – Instant Zone

An Instant Zone (Contact ID Event Code 130) immediately sounds the sirens and operates the dialer when it is unsealed after the Exit Timer expires.

If an Instant Zone is not restored when the system is disarmed, a Zone Restore Report is automatically sent to the receiving party.

1 – Handover Zone

A Handover Zone (Contact ID Event Code 130) acts as an Instant Zone if it is activated by itself. If a Handover Zone is activated after a Delay Zone, the remaining Delay Time is handed over from the Delay Zone to the Handover Zone.

Handover can be sequential or non-sequential. The default settings is sequential handover. You can disable sequential handover by disabling Option 8 in Location 426 (refer to Section 18.3 System Options 3 on page 74).

If a Handover Zone is not restored when the system is disarmed, a Zone Restore Report is automatically sent to the receiving party.

2 – Delay-1 Zone

A Delay-1 Zone (Contact ID Event Code 130) has a delay time determined by the value in Locations 398 and 399 (refer to Section 17.2 Entry Timer 1 on

page 70). After Entry Time expires, the system activates an alarm.

If a Delay-1 Zone is not restored when the system is disarmed, a Zone Restore Report is sent to the receiving party.

3 – Delay-2 Zone

A Delay-2 Zone (Contact ID Event Code 130) has a delay time determined by the value in Locations 400 and 401 (refer to Section 17.3 Entry Timer 2 on

page 71). After Entry Time expires, the system activates an alarm.

If a Delay-2 Zone is not restored when the system is disarmed, a Zone Restore Report is sent to the receiving party.

4 – Reserved

5 – Reserved

6 – 24-Hour Medical Zone

A24-Hour Medical Zone (Contact ID Event Code

100) is always ready to activate the dialer, horn speaker, bell, and strobe, regardless of whether the system is armed or disarmed. A Medical Report is sent to the base station receiver. A 24-Hour Medical Zone does not send a Restore Report until the zone is restored.

7 – 24-Hour Panic Zone

A 24-Hour Panic Zone (Contact ID Event Code 120) is always ready to activate the dialer, horn speaker, bell, and strobe, regardless of whether the system is armed or disarmed. A Panic Report is sent to the base station receiver. A 24-Hour Panic Zone does not send a Restore Report until the zone is restored.

Bosch Security Systems, Inc. 12/08 F01U089401-02 55