ICP-CC404 Installation Guide 6.0 System Functions
When arming the system in AWAY Mode, the control panel automatically dials the telecommunication exchange to redirect all calls to your mobile phone, pocket pager, or answering service. When activated, your telephone still allows outgoing calls.
Contact your telecommunications provider for more information on call forward operations.
Table 22: Telco Arming or Disarming Dialing Digits
|
|
|
|
Digit | Number to | Digit | Number to |
Required | Program | Required | Program |
0 | 0 | 8 | 8 |
1 | 1 | 9 | 9 |
|
|
|
|
2 | 2 | 10 | refer to 0 |
3 | 3 | 11 | * 1 |
4 | 4 | 12 | * 2 |
5 | 5 | 4 sec pause | * 3 |
6 | 6 | break | * 4 |
7 | 7 | 15 | * 5 |
Table 23: | Codepad Indicators When Changing | ||||||||
|
| the Telco Arming or Disarming | |||||||
|
| Sequence |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Zone Indicators |
|
| MAINS | |||
Digit | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Indicator |
0 |
|
|
|
|
|
|
|
| X |
1X
2
X
3 | X |
4
X
5 | X |
6
X
7 | X |
8
X
9 | X |
| X | ||||
11 | X |
|
|
|
|
| X |
12 |
| X |
|
| X | ||
Pause |
|
| X |
|
|
| X |
Break |
|
|
| X |
|
| X |
15 |
|
|
|
| X |
| X |
To program the Telco arming sequence – easy call forward (no answer on):
1.Enter the Installer Code and press [3][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Press [1][AWAY] to change the Telco arming sequence. Three beeps sound.
If a call forwarding sequence is already programmed, the sequence appears one digit at a time using the remote codepad indicators. Refer to Table 23 on page 29 for the indicators and their meanings.
If there is no call forward sequence programmed, an additional two beeps sound after entering this mode. These two beeps normally sound after the last digit of the call forward sequence is displayed.
3.Press [STAY][1 6 1] and enter the phone number to which you want calls from the control panel diverted.
4.Press [STAY][2][AWAY].
Two beeps sound and the system returns to the disarmed state.
Example
If you want to automatically divert all unanswered incoming calls to another telephone number (for example, 9672 1777) when the system is armed in AWAY Mode, enter:
[1 2 3 4 3][AWAY][1][AWAY][STAY] [1 6 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the Telco arming sequence at any time.
To disable the Telco arming sequence:
Enter the Installer Code and press [3][AWAY][1] [AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy call forward (no answer off):
1.Enter the Installer Code and press [3][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Press [2][AWAY] to change the Telco disarming sequence.
Three beeps sound.
If a Telco disarming sequence is already programmed, the sequence appears one digit at a time using the remote codepad indicators. Refer to Table 23 on page 29 for the indicators and their meanings.
If there is no Telco disarming sequence programmed, an additional two beeps sound after entering this mode. These two beeps normally sound after the last digit of the sequence is shown.
3.Press [STAY][2 6 1][STAY][2][AWAY].
Two beeps sound and the system returns to the disarmed state.
You can suspend the Telco disarming sequence at any time.
Bosch Security Systems, Inc. 12/08 | 29 |