Bosch Appliances ICP-CC404 manual 374 to 392 to Strobe Output

ICP-CC404 Installation Guide	22.0 Programming Sheets
Location		Options/Notes			Default/
Function				Programming Entry
350 to 351			Location 350: tens digit		10	7
System Status – AC Fail Restore Report			Location 351: units digit
Refer to page 62
352 to 353			Location 352: tens digit		10	1
System Status – Low Battery Report			Location 353: units digit
Refer to page 62
354 to 355			Location 354: tens digit		10	6
System Status – Low Battery Restore Report			Location 355: units digit
Refer to page 63
356 to 358		Location 356: Code retry limit (0 = unlimited)			6 7 12
System Status – Access Denied (Code Retry)			Location 357: tens digit
Refer to page 63			Location 358: units digit

359				0	No System Status Reports allowed																	1
System Status Reporting Options				1	Report to Receiver 1
Refer to page 63				2	Report to Receiver 2
				4	Report to both Receiver 1 and Receiver 2
				8	Report to Receiver 2 only if Receiver 1 fails
360 to 366						Location 360: Hour of day (tens digit)												0 0 0 0 7 1 0
Test Report Time (Automatic)						Location 361: Hour of day (units digit)
Refer to page 63						Location 362: Minute of day (tens digit)
						Location 363: Minute of day (units digit)
						Location 364: Test Report (tens digit)
						Location 365: Test Report (units digit)
						Location 366: Repeat interval in days
367				0	No Test Reports allowed																	1
Test Reporting Dialer Options				1	Report to Receiver 1
Refer to page 64				2	Report to Receiver 2
				4	Report to both Receiver 1 and Receiver 2
				8	Report to Receiver 2 only if Receiver 1 fails
368 to 397			Output 1		1 14 0 0 0 0									Relay Output		1 15 1 0 0 0
Outputs								(Horn speaker)										(Sirens running)
Refer to page 64		(368 to 373)												(386 to 391)
					2		7		10	2	1	3				0		13	2	1	0	1
			Output 2		(Fire alarm with verification)								Codepad Buzzer				(Entry/exit plus day alarm)
		(374 to 379)												(392 to 397)
					6		0		6	4	0	8
		Strobe Output				(Strobe – reset after 8 hr)
		(380 to 385)
	The first two locations (from the left) of the output definition provide the Event Code. For a complete list
	of the Output Event Codes, refer to Section 16.2 Output Event Types on page 65.
	The third location of the output definition is the output polarity. The options are:
		0	Disabled											8 Normally low, going open
		1	Normally open, going low										9		Normally low, pulsing open
		2	Normally open, pulsing low										10		Normally low, one shot open
		3	Normally open, one shot low										11		Normally low, one shot open (can restart)
		4	Normally open, one shot low (can restart)										12		Normally low, one shot open (can reset)
		5	Normally open, one shot low (can reset)										13		Normally low, one shot open (alarm)
		6	Normally open, one shot low (alarm)										14		Normally low, latching open
		7	Normally open, latching low
	The fourth location of the output definition is the time base. The options are:
		1	200 ms										3		1 min
		2	1 sec										4		1 hr

90 Bosch Security Systems, Inc. 12/08 F01U089401-02