ICP-CC404 Installation Guide 11.0 Dialer Information
System Status
The system status information is shown by four digits, which are defined in Figure 6 on page 45. The first digit indicates whether the system is armed or disarmed. The second digit indicates whether a codepad alarm was activated by the operator (refer to Section 4.7 Codepad Duress Alarm on page 21 through Section 4.10 Codepad Medical Alarm on page 21 for more information). The third digit indicates the status of the AC MAINS supply. The fourth digit indicates whether a system fault occurred at the control panel (refer Section 4.12 Fault Analysis Mode on page 22 for more information.
11.0 Dialer Information
This section outlines the programming information required for the
The control panel can report event information from two
2.You can program each dialer with two separate telephone numbers, handshake tone, reporting format type, and Subscriber ID Number.
Example
You can set up Dialer 1 to report in Domestic Dialing Format to Receiver 1 and set up Dialer 2 to report to a base station receiver in Contact ID Format only if Dialer 1 is unsuccessful.
To program a telephone number:
You must program a 0 as 10. Each location in the primary, secondary, and callback telephone numbers stores one digit of the telephone number.
You must insert a 0 at the end of a telephone number to indicate to the dialer the end of the telephone number is reached. The dialing sequence ends when a 0 appears. Refer to Table 38.
Table 38: Dialing Digits
|
|
|
|
Digit | Number to | Digit | Number to |
Required | Program | Required | Program |
terminator | 0 | 8 | 8 |
1 | 1 | 9 | 9 |
|
|
|
|
2 | 2 | 0 | 10 |
3 | 3 | * | 11 |
|
|
|
|
4 | 4 | # | 12 |
5 | 5 | 4 sec pause | 13 |
|
|
|
|
6 | 6 | break | 14 |
7 | 7 |
|
|
|
|
|
|
Example
To program the telephone number 9672 1055 as the Primary Telephone Number for Receiver 1, program the following sequence into Locations 000 to 015:
[9 6 7 2 1 10 5 5 0 0 0 0 0 0 0 0]
To enter a
Example
To program the number 02 pause 9 672 1055, enter:
[10 2 13 9 6 7 2 1 10 5 5 0 0 0 0 0].
Table 38 shows how to program the numbers, keys, and functions for a telephone number.
11.1Primary Telephone Number for Receiver 1 and Receiver 2
Program the Primary Telephone Number for Receiver 1 in Locations 000 to 015.
Program the Primary Telephone Number for Receiver 2 in Locations 040 to 055.
The default value for both telephone numbers is 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0.
When the control panel sends a report, Number this number to contact the monitoring station or pager, for example. If the call is successful, the information is sent and the dialer returns to Standby Mode.
If unsuccessful, the dialer attempts two more calls using the Primary Telephone Number for Receiver 1. If these calls are unsuccessful, the dialer calls the Secondary Telephone Number for Receiver 1 up to three times. If the dialing sequence is still unsuccessful, the control panel repeats this sequence by dialing the Primary and Secondary Telephone Numbers for Receiver 2 (if they are programmed).
If the first six attempts are unsuccessful and no telephone numbers for Receiver 2 are programmed, this procedure is repeated only once, for up to twelve call attempts per alarm, after ten min.
If the Primary and Secondary Telephone Numbers for Receiver 2 are also programmed, the control panel attempts up to 24 calls per alarm.
Contact your monitoring station or pager company for the correct telephone numbers before you program these locations.
46 | Bosch Security Systems, Inc. 12/08 |