Wayne-Dalton 9800 Series Attaching Disconnect Cables, Mounting Disconnect, Handle Bracket

Page 29

25

Tools Needed:

Pliers

Attaching Disconnect Cables

NOTE: See idrive® main installation and owners manual for idrive® parts.

Attach the loose disconnect cable (located in opener hardware bag) to the opener with the “S” hook. Close both ends of the “S” hook with pliers, to lock assembly together.

Thread the disconnect cable (behind the counterbalance cable) through the hole in the right hand end bracket. Remove all slack between opener and right end bracket.

S-Hook

Disconnect

Cable

Hole in Right

End Bracket

Right Side of

End Bracket

Hole in

Close “S” Hook

End Bracket

INSTALLATION

26

Mounting Disconnect

Handle Bracket

Tools Needed:

NOTE: See idrive® main installation and

Pencil

owners manual for idrive® parts.

Tape measure

Mark a location on the right jamb, 6

1/8” Drill Bit

feet above the floor to mount the

7/16” Socket

disconnect handle bracket.

 

Driver

Drill 1/8” pilot holes for the lag screws.

Power Drill

 

Align top of the bracket with the mark. Fasten bracket to the jamb with

(2) 1/4” x 1-1/2" lag screws.

6 ft.

(2) 1/4” x 1-1/2” Lag Screws

Disconnect

Handle Bracket

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 29 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Important Notice Series 4 SectionTable of Contents PRE-INSTALLATION Package ContentsDoor Section Identification Tools Required Power Drill3/16 Drill Bits GlovesFailure to use approved Torsion Spring Removal For Standard LiftWinding bars can cause spring Energy to be released Suddenly, resulting in severe Or fatal injuryUnwind Springs Bracket and Drive Gear TorqueMaster SpringRemoval Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Be installed as shownTap the horizontal angle towards AsideBrackets Installing Q.I. Jamb Brackets Vertical Track Bottom SectionStacking Sections With the second set of holes from Top BracketsEndcap 20 x 5/8 carriage boltsOperator Bracket Top Section Injury Attaching Horizontal Track toDo not Raise Door Until Hex nuts This stepAdjusting Top Brackets TorqueMaster Spring Tube Must install the center bracket bushingCenter Bracket Bushing Continue with Step Idrive opener on your garage door, youIdrive Installation Cable Drum Installation End Brackets Drive Gear InstallationTools Needed Lubricating Oil Repeat for left hand side.`Securing Center Bracket Assembly Counter InstallationInstallations on page 35, Figure B Repeat for left hand side for double spring applicationsPositioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Disconnect handle Disconnect handle. ThreadBracket Secure disconnect cable toTools Needed Vice Clamp Cable AdjustmentsTools Needed Locking Pliers Flat Tip Screwdriver Important do not USE Impact GUN to Wind SpringsRecommended Spring Turns Setting Spring TensionWinding Bolt Rotation Rear Support Drum Wrap InstallationKeep horizontal track Parallel and within 3/4 Maximum of door edgeAttach horizontal tracks to the rear Adjust weather seal or door stop ifTools Needed Weather seal or door stop to both doorDoorMaster TM Bracket Side LockNo Scew EYE Pull Rope Bottom Bracket Tools Needed Power Drill Drill BitPull Rope Operator Must be Tested AT Time Trolley OperatorResult in Severe or Fatal Injury Door is fully open trolley rail willGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingThank you for your purchase Lifetime Limited Warranty Model
Top Page Image Contents