Wayne-Dalton 9800 Series Disconnect handle. Thread, Bracket, Secure disconnect cable to

Page 30

 

 

27

Attaching Disconnect Handle

 

 

NOTE: See idrive® main installation and

Tools Needed:

Phillips head

owner’s manual for idrive® parts.

 

screwdriver

Note: Bring motor to the down position

Wire cutters

by pulling the disconnect cable. Insure

 

opener disconnect teeth are engaged

 

Ibefore installing disconnect handle.

 

Start the #6-20 x 1/2" screw into the

 

disconnect handle. Thread the

 

disconnect cable through the top of the

 

disconnect handle bracket and then the

 

disconnect handle.

 

Locate the disconnect handle in full

 

upper position of disconnect handle

 

bracket.

 

Remove all disconnect cable slack

 

between the opener and the top of the

 

disconnect handle bracket. Tighten

 

#6-20 x 1/2" screw into the disconnect

 

handle until snug, and then tighten

 

screw an additional 1 to 1-1/2 turns to

 

secure disconnect cable to the

 

disconnect handle. Trim off excess cable

 

from bottom of the disconnect handle.

 

CAUTION: Pull Cable only taut

 

enough to remove the Cable slack.

 

Pulling the Cable more could

 

cause Opener to disconnect from

 

the TorqueMaster® Spring Tube.

 

Apply emergency disconnect label next

 

to the mounted bracket. Use

 

mechanical fasteners if adhesive will

 

not adhere.

 

Using the emergency disconnect, pull

 

disconnect handle downwards and

 

place it in the manual door operated

 

position (Use disconnect label for

 

reference). Motor will be rotated 90°

 

from its packaged position.

 

If motor does not pivot 90°, see

 

troubleshooting section in the main

 

installation and owners manual of your

 

idrive® opener

 

 

Upper Position

Emergency Disconnect

 

Label

#6-20 x 1/2”

 

Screw

 

Handle

 

Disconnect

 

Cable

 

Disconnect

 

Handle

 

Bracket

 

Manual operated position

Motor operated position

30Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 30
Contents Series 4 Section Important NoticeTable of Contents Package Contents PRE-INSTALLATIONDoor Section Identification 3/16 Drill Bits Power DrillTools Required GlovesWinding bars can cause spring Energy to be released Torsion Spring Removal For Standard LiftFailure to use approved Suddenly, resulting in severe Or fatal injuryUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening Tools Needed None InstallationAttaching Quick Install Flag Angle to Vertical Track FlagangleTap the horizontal angle towards Be installed as shownHorizontal Angle AsideBrackets Installing Q.I. Jamb Brackets Bottom Section Vertical TrackStacking Sections Endcap Top BracketsWith the second set of holes from 20 x 5/8 carriage boltsOperator Bracket Top Section Attaching Horizontal Track to Do not Raise Door UntilInjury This step Hex nutsAdjusting Top Brackets Center Bracket Bushing Must install the center bracket bushingTorqueMaster Spring Tube Continue with Step Idrive opener on your garage door, youIdrive Installation Cable Drum Installation Tools Needed Lubricating Oil Drive Gear InstallationEnd Brackets Repeat for left hand side.`Installations on page 35, Figure B Counter InstallationSecuring Center Bracket Assembly Repeat for left hand side for double spring applicationsPositioning Support Bracket Attaching Disconnect Cables Mounting DisconnectHandle Bracket Bracket Disconnect handle. ThreadDisconnect handle Secure disconnect cable toTools Needed Locking Pliers Flat Tip Screwdriver Cable AdjustmentsTools Needed Vice Clamp Important do not USE Impact GUN to Wind SpringsSetting Spring Tension Winding Bolt RotationRecommended Spring Turns Keep horizontal track Drum Wrap InstallationRear Support Parallel and within 3/4 Maximum of door edgeTools Needed Adjust weather seal or door stop ifAttach horizontal tracks to the rear Weather seal or door stop to both doorSide Lock DoorMaster TM BracketTools Needed Power Drill Drill Bit Pull RopeNo Scew EYE Pull Rope Bottom Bracket Result in Severe or Fatal Injury Trolley OperatorOperator Must be Tested AT Time Door is fully open trolley rail willAcrylic Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model Thank you for your purchase