Wayne-Dalton 9800 Series installation instructions Positioning Support Bracket

Page 28

24

Positioning Support Bracket

 

 

 

 

 

 

 

 

 

Tools Needed:

NOTE: See idrive® main installation and

45 angle

Antenna

mounting

owners manual for idrive® parts.

 

wire

 

Power Drill

 

 

surface

 

 

 

 

 

1/8” Drill Bit

NOTE: idrive® must be installed on a

 

 

 

 

solid mounting surface.

 

 

 

 

7/16” Socket

 

 

 

 

 

 

 

 

 

Driver

Locate the mounting surface. The

 

 

 

 

 

 

 

 

 

 

mounting surface is a vertical board

 

 

 

 

 

running directly above the center of the

 

 

TorqueMaster®

 

door. Remove (2) 1/4”-20 flange nuts

 

 

 

 

 

spring tube

 

from bottom of opener.

 

 

 

 

 

 

SUPPORT

 

 

 

 

 

 

NOTE: Do not discard flange nuts.

 

 

 

BRACKET

 

1/4” X 1-1/2”

 

 

 

 

 

 

 

 

 

Place the support bracket underneath

LAG SCREW

 

 

 

 

(Header)

 

 

 

 

opener, to the right side of motor,

 

 

 

 

TOP OF DOOR

 

 

 

 

centered on mounting surface. Using a

1/4” - 20

 

 

 

 

 

 

 

tape measure, level the bottom of the

 

FLANGE NUTS

 

 

 

TorqueMaster® spring tube to the top of

 

 

 

 

 

the door section with the idrive® resting

 

 

 

 

 

on the support bracket. Once

 

 

 

 

 

TorqueMaster® spring tube is level, drill

 

 

 

mounting

 

1/8” pilot holes for the lag screws. Then

 

 

 

studs

 

secure support bracket to the mounting

 

 

 

 

 

surface with (2) 1/4” x 1-1/2" lag

 

 

 

 

 

screws.

 

mounting

 

 

 

 

 

bracket

 

IMPORTANT: TorqueMaster® spring

 

studs

 

 

 

slots

 

 

 

 

 

tube must be level after support

 

 

 

 

 

bracket is fastened to mounting

 

 

 

 

 

surface.

 

 

 

 

 

NOTE: If wood mounting surface is

 

 

 

support

 

behind dry wall, use 1/4” x 2” lag

TorqueMaster®

 

 

bracket

 

screws.

spring tube

 

 

 

 

 

 

 

 

 

Lift and slide the opener over the

 

 

 

 

 

support bracket, aligning the mounting

 

 

 

 

 

studs with the bracket slots. Loosely

 

 

 

 

 

fasten to mounting studs with the (2)

 

 

 

 

 

1/4”-20 flange nuts.

 

(2) 1/4” - 20

 

NOTE: Do not tighten 1/4”-20 flange

 

flange nuts

 

 

 

 

 

 

nuts to opener studs at this time.

 

 

 

 

 

Remove the temporary orange label

 

 

 

 

 

holding the antenna wire. Straighten

 

 

 

 

 

antenna wire and angle it 45 degrees to

 

 

 

 

 

the right.

 

 

 

 

 

NOTE: Do not coil the antenna wire.

“x”

“x”

 

“x”

 

This will reduce the radio signal range.

 

 

 

 

 

 

 

top section

 

 

 

 

Using a tape measure, maintain an equal measurement “x”

 

 

(top of door to bottom of Torquemaster® tube) at both

 

 

ends and the center.

 

 

28Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 28
Contents Series 4 Section Important NoticeTable of Contents Package Contents PRE-INSTALLATIONDoor Section Identification Power Drill Tools Required3/16 Drill Bits GlovesTorsion Spring Removal For Standard Lift Failure to use approvedWinding bars can cause spring Energy to be released Suddenly, resulting in severe Or fatal injuryUnwind Springs Removal TorqueMaster SpringBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening Installation Attaching Quick Install Flag Angle to Vertical TrackTools Needed None FlagangleBe installed as shown Horizontal AngleTap the horizontal angle towards AsideBrackets Installing Q.I. Jamb Brackets Bottom Section Vertical TrackStacking Sections Top Brackets With the second set of holes fromEndcap 20 x 5/8 carriage boltsOperator Bracket Top Section Do not Raise Door Until Attaching Horizontal Track toInjury This step Hex nutsAdjusting Top Brackets Must install the center bracket bushing TorqueMaster Spring TubeCenter Bracket Bushing Continue with Step Idrive opener on your garage door, youIdrive Installation Cable Drum Installation Drive Gear Installation End BracketsTools Needed Lubricating Oil Repeat for left hand side.`Counter Installation Securing Center Bracket AssemblyInstallations on page 35, Figure B Repeat for left hand side for double spring applicationsPositioning Support Bracket Mounting Disconnect Attaching Disconnect CablesHandle Bracket Disconnect handle. Thread Disconnect handleBracket Secure disconnect cable toCable Adjustments Tools Needed Vice ClampTools Needed Locking Pliers Flat Tip Screwdriver Important do not USE Impact GUN to Wind SpringsWinding Bolt Rotation Setting Spring TensionRecommended Spring Turns Drum Wrap Installation Rear SupportKeep horizontal track Parallel and within 3/4 Maximum of door edgeAdjust weather seal or door stop if Attach horizontal tracks to the rearTools Needed Weather seal or door stop to both doorSide Lock DoorMaster TM BracketPull Rope Tools Needed Power Drill Drill BitNo Scew EYE Pull Rope Bottom Bracket Trolley Operator Operator Must be Tested AT TimeResult in Severe or Fatal Injury Door is fully open trolley rail willCleaning Your Steel And Fiberglass Garage Door Glass Cleaning InstructionsAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model Thank you for your purchase