Wayne-Dalton 9800 Series Top Brackets, With the second set of holes from, Endcap, For other side

Page 17

10

Top Brackets

 

 

 

2nd set of holes

 

Tools Needed:

To install the L-shaped top brackets, align

from bottom

 

 

 

Power Drill

the bottom holes in the top bracket base

 

 

with the second set of holes from the

 

 

7/16” Socket

 

 

endcap.

 

 

Driver

 

 

 

 

Fasten using (4) 1/4” - 14 x 5/8” self

 

 

 

tapping screws. Secure the top bracket

 

 

 

slide to the bracket base loosely using (2)

 

 

 

1/4” - 20 x 5/8” carriage bolts and

 

 

 

(2) 1/4” - 20 flanged hex nuts. The bracket

 

 

 

will be tightened and adjusted in Step 15.

 

 

 

Insert rollers into top bracket slide. Repeat

TOP BRACKET BASE

 

 

for other side.

 

 

 

TOP SECTION

 

 

 

2nd set of holes

(4) 1/4” - 14 x 5/8”

 

 

SELF TAPPING

 

 

from bottom

 

 

SCREWS

 

 

 

 

 

 

(2) 1/4” - 20 x 5/8”

 

 

 

CARRIAGE BOLTS

 

 

TOP BRACKET SLIDE

 

 

 

TOP SECTION

 

 

 

 

(2) 1/4” - 20

 

 

 

FLANGED HEX

 

 

 

NUTS

 

 

 

ROLLER

 

 

TOP SECTION

 

 

 

 

TOP BRACKET SLIDE

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 17 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

INSTALLATION

Image 17
Contents Important Notice Series 4 SectionTable of Contents PRE-INSTALLATION Package ContentsDoor Section Identification Tools Required Power Drill3/16 Drill Bits GlovesFailure to use approved Torsion Spring Removal For Standard LiftWinding bars can cause spring Energy to be released Suddenly, resulting in severe Or fatal injuryUnwind Springs Bracket and Drive Gear TorqueMaster SpringRemoval Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Be installed as shownTap the horizontal angle towards AsideBrackets Installing Q.I. Jamb Brackets Vertical Track Bottom SectionStacking Sections With the second set of holes from Top BracketsEndcap 20 x 5/8 carriage boltsOperator Bracket Top Section Injury Attaching Horizontal Track toDo not Raise Door Until Hex nuts This stepAdjusting Top Brackets TorqueMaster Spring Tube Must install the center bracket bushingCenter Bracket Bushing Continue with Step Idrive opener on your garage door, youIdrive Installation Cable Drum Installation End Brackets Drive Gear InstallationTools Needed Lubricating Oil Repeat for left hand side.`Securing Center Bracket Assembly Counter InstallationInstallations on page 35, Figure B Repeat for left hand side for double spring applicationsPositioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Disconnect handle Disconnect handle. ThreadBracket Secure disconnect cable toTools Needed Vice Clamp Cable AdjustmentsTools Needed Locking Pliers Flat Tip Screwdriver Important do not USE Impact GUN to Wind SpringsRecommended Spring Turns Setting Spring TensionWinding Bolt Rotation Rear Support Drum Wrap InstallationKeep horizontal track Parallel and within 3/4 Maximum of door edgeAttach horizontal tracks to the rear Adjust weather seal or door stop ifTools Needed Weather seal or door stop to both doorDoorMaster TM Bracket Side LockNo Scew EYE Pull Rope Bottom Bracket Tools Needed Power Drill Drill BitPull Rope Operator Must be Tested AT Time Trolley OperatorResult in Severe or Fatal Injury Door is fully open trolley rail willGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingThank you for your purchase Lifetime Limited Warranty Model