Henny Penny OFE- 291 manual Programming

Page 23

 

 

 

 

Model OFE- 291

3-15. PROGRAMMING

8. Press and release

and “2. STEP 2 AT” shows in

(Continued)

display, along with a step 2 time. If no step 2 is desired, set

 

 

time to “0:00” and press

. If a step 2 is desired, press

 

and set a time. Then press

to set the

 

temperature.

 

 

 

Up to 10 steps can be programmed for a product, repeating the above step for each cooking step.

9.Press and release and “ALARM – 1 AT 0:00”

shows in the display. Press and release to set an

alarm. Ex: If a Cook Cycle was set at 3 minutes, and an alarm was to go off after 30 seconds into the Cook Cycle, “2:30” would be set in the display at this time. When the timer counts down to 2:30 the alarm sounds.

After the alarm time is set, press and “ALARM” and “TYPE” flashes in the display, with the alarm type on the right side of the display. “TIME”, “SHAKE”, “STIR”, “ADD”,

and “LID” can be set by pressing . An alarm sounds and alarm type flashes, prompting the operator to shake the basket, stir the product, or add product. If “TIME” is selected, the time remaining flashes in the display. If “LID” is selected, “CLOSE LID” flashes in the display. The timer count-down pauses until the lid is closed and is pressed to restart the timer.

Up to 4 alarms can be programmed. After the first one is

set, the other alarms can be accessed by pressingagain.

10.Press and release until “QUALITY TMR” shows in

the display along with the preset holding time. Press and

release

to adjust the holding time, up to 59:59.

To exit the Program Mode at any time, press and hold for 2 seconds.

3-23

403

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operation Operating Components LID Operation Description Function SwitchesIndicators Switches and Indicators Description Function Model OFE 403 Clock SET Clock SET Filling or Adding Shortening Product Racking Recommendations LINE. Failure to Follow These Instruc Above the Upper Frypot LevelindicatorBasic Operation Be Certain the Shortening is NeverAllow fryer to heat until Illuminates Unlatch and raise the lid cautiously Personal INJURY, FIRE, AND/OR Property Care ShorteningShortening Overflowingthe Frypot Which could Result in Serious BurnsFiltering Instructions Filtering Instructions Is in the OFF POSITION. ALSO, USE a DRY Rinse Hose When the Main Power SwitchFiltering Instructions Only Connectand Disconnect the FilterEnvelope Filter Pump Motor PROTECTOR-MANUAL Reset Cleaningthe Frypot Drained by slowly pulling the drain handle out towards you If hot shortening is present in the frypot, it must beDoes not boil over causing damage to controls Cleaning the FrypotPreventive Procedure FrequencyCleaning Nylatrons Monthly MaintenanceChange Product Names ProgrammingProgramming Go to Idle after Done? Filter Cycle Mode OptionalProgramming Global Erase a Prod Preset a Prod Erase ALL Mode Special ProgramAudio Tone SP-5 Language SP-2 ModeAudio Volume SP-4 System Initialization SP-3Type of shortening to be melted Liquid or Solid SP-6 Idle Mode SP-7Mixed Press SP-8C shows in the display, if YES To filter the shortening. Press To change Special Program ScheduleClean-Out Temperature Sp-11 Product Buttons Sp-9 ModeClean-Out Temperature Sp-10 Usage Code Change SP-16 Mode Program Code Change SP-15Code Change Mode Shows in display If not satisfied with code, pressData LOGGING, Heat CONTROL, Tech MODE, and Stat Mode If satisfied with code, pressPress to continue to Last Load Function Displayex Information Mode Last LoadFunction Display EX Information ModeOutp H* P Analog 1 OIL TMPCPU TMP
Top Page Image Contents