Henny Penny OFE- 291 manual Language SP-2 Mode, System Initialization SP-3, Audio Volume SP-4

Page 28

Model OFE- 291

3-16. SPECIAL PROGRAM

Language (SP-2)

 

 

MODE (Continued)

a. Follow steps 1 and 2 above.

 

 

b. Press and release

button. “SP-2” and

 

 

“LANGUAGE” flashes on the display, along with the

 

 

language (Ex:” 1.ENGL”)

 

 

c. To toggle to the desired language, press and release

.

System Initialization (SP-3)

This step resets the controls, but doesn’t erase product settings.

a.Follow steps 1and 2 above.

b.Press and release twice. “SP-3” and “DO SYSTEM INIT” flashes on the display, along with “INIT’.

c.Press and hold . “INIT” shows on the display,

a tone sounds, and “IN 3”, “IN 2”, “ IN 1” flashes on the right side of the display. When “INIT” starts flashing on

the left side of the display, release . When “ DONE” shows on the display, the initialization is complete, and the controls now have factory preset parameters.

Audio Volume (SP-4)

The volume of the speaker can be adjusted. a. Follow steps 1 and 2 above.

b. Press 3 times. “SP-4” and “AUDIO VOLUME” flashes on the display, along with the volume value.

c.Press to adjust the speaker volume; 10 the maximum value and 1 the minimum.

Audio Tone (SP-5)

The tone of the speaker can be adjusted.

a.Follow steps 1 and 2 above.

b.Press 4 times. “SP-5” and “AUDIO TONE (HZ)” flashes on the display, along with the tone value.

c. Press to adjust the tone of the speaker; 2000 the maximum,50theminimum.

403

3-28

Image 28
Contents Operation Operating Components LID Operation Indicators SwitchesDescription Function Switches and Indicators Description Function Model OFE 403 Clock SET Clock SET Filling or Adding Shortening Product Racking Recommendations Above the Upper Frypot Levelindicator Basic OperationBe Certain the Shortening is Never LINE. Failure to Follow These InstrucAllow fryer to heat until Illuminates Unlatch and raise the lid cautiously Care Shortening Shortening Overflowingthe FrypotWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR PropertyFiltering Instructions Filtering Instructions Rinse Hose When the Main Power Switch Filtering InstructionsOnly Connectand Disconnect the Filter Is in the OFF POSITION. ALSO, USE a DRYEnvelope Filter Pump Motor PROTECTOR-MANUAL Reset Cleaningthe Frypot If hot shortening is present in the frypot, it must be Drained by slowly pulling the drain handle out towards youCleaning the Frypot Does not boil over causing damage to controlsProcedure Frequency Cleaning Nylatrons MonthlyMaintenance PreventiveProgramming Change Product NamesProgramming Programming Filter Cycle Mode OptionalGo to Idle after Done? Global Erase a Prod Preset a Prod Erase ALL Special Program ModeLanguage SP-2 Mode Audio Volume SP-4System Initialization SP-3 Audio Tone SP-5Idle Mode SP-7 Type of shortening to be melted Liquid or Solid SP-6Mixed Press SP-8C shows in the display, if YES Special Program Schedule To filter the shortening. Press To changeClean-Out Temperature Sp-10 Product Buttons Sp-9 ModeClean-Out Temperature Sp-11 Mode Program Code Change SP-15 Usage Code Change SP-16Mode Shows in display If not satisfied with code, press Data LOGGING, Heat CONTROL, Tech MODE, and Stat ModeIf satisfied with code, press Code ChangePress to continue to Last Load Information Mode Last Load Function DisplayexInformation Mode Function Display EXOutp H* P CPU TMP OIL TMPAnalog 1