Henny Penny OFE- 291 manual Type of shortening to be melted Liquid or Solid SP-6, Idle Mode SP-7

Page 29

Model OFE- 291

3-16. SPECIAL PROGRAM

Type of shortening to be melted - Liquid or Solid (SP-6)

MODE (Continued)

The Melt Cycle can be set to the type of shortening being used.

 

a. Follow steps 1 and 2 above.

 

b. Press and release

5 times. “SP-6”

 

and “MELT CYCLE SELECT” flashes on the display,

 

along with “l=LIQ” or “2=SOLID”.

 

c. Press

to toggle from one type to another.

The type of shortening being used in the fryer determines the amount of heat applied during the Melt Cycle. If the controls are set to the solid setting, less heat is applied to the shortening, than if the controls were set to liquid. Too much heat applied to solid shortening causes much smoking, and could cause a fire. Match this setting to the type of shortening being used at the time.

When using new shortening, it is recommended to melt the shortening on an outside source before placing shortening in the frypot. Unless elements are completely covered in shortening, fire or damage to the frypot could result.

Idle Mode (SP-7)

A programmed Idle Mode allows the shortening temperature to drop to a lower temperature when not in use. This saves on the shortening and utilities.

a.Follow steps 1and 2 above.

b.Press and release 6 times. “SP-7” and “IDLE

MODE ENABLED?” flashes in the display, along with “NO” or “YES”.

c. Press and release

to toggle from NO to YES,

or vice versa.

 

d. With “YES” in the display, the Idle Mode is enabled.

Press and release

. “SP-7A” and

“IDLE SETPT TEMP” shows in the display, along with

the preset temperature.

 

3-29

403

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Operation Operating Components LID Operation Description Function SwitchesIndicators Switches and Indicators Description Function Model OFE 403 Clock SET Clock SET Filling or Adding Shortening Product Racking Recommendations Basic Operation Above the Upper Frypot LevelindicatorBe Certain the Shortening is Never LINE. Failure to Follow These InstrucAllow fryer to heat until Illuminates Unlatch and raise the lid cautiously Shortening Overflowingthe Frypot Care ShorteningWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR PropertyFiltering Instructions Filtering Instructions Filtering Instructions Rinse Hose When the Main Power SwitchOnly Connectand Disconnect the Filter Is in the OFF POSITION. ALSO, USE a DRYEnvelope Filter Pump Motor PROTECTOR-MANUAL Reset Cleaningthe Frypot Drained by slowly pulling the drain handle out towards you If hot shortening is present in the frypot, it must beDoes not boil over causing damage to controls Cleaning the FrypotCleaning Nylatrons Monthly Procedure FrequencyMaintenance PreventiveChange Product Names ProgrammingProgramming Go to Idle after Done? Filter Cycle Mode OptionalProgramming Global Erase a Prod Preset a Prod Erase ALL Mode Special ProgramAudio Volume SP-4 Language SP-2 ModeSystem Initialization SP-3 Audio Tone SP-5Type of shortening to be melted Liquid or Solid SP-6 Idle Mode SP-7Mixed Press SP-8C shows in the display, if YES To filter the shortening. Press To change Special Program ScheduleClean-Out Temperature Sp-11 Product Buttons Sp-9 ModeClean-Out Temperature Sp-10 Usage Code Change SP-16 Mode Program Code Change SP-15Data LOGGING, Heat CONTROL, Tech MODE, and Stat Mode Mode Shows in display If not satisfied with code, pressIf satisfied with code, press Code ChangePress to continue to Last Load Function Displayex Information Mode Last LoadFunction Display EX Information ModeOutp H* P Analog 1 OIL TMPCPU TMP
Top Page Image Contents