Henny Penny OFE- 291 manual Oil Tmp, Cpu Tmp, Analog 1

Page 40

Model OFE- 291

3-18. INFORMATION MODE

Press

and “6. PMP_ AIR_” shows in display.

(Continued)

 

 

 

 

Press

to view the amp “DRAW” status of the pump motor

 

output and air valve output. “PMP ” and “AIR ” in the

 

display means the amps are good. Aflashing “X” behind the

 

“PMP” or “AIR” means too much current.

 

Press

to view the No Connect/Ground (“NC/GND”)

 

status of each output. This monitors a possible problem with

 

the relays on the output PC board.

 

Press

to continue onto the OIL TMP reading.

 

7. OIL TMP

 

 

This step shows the present peanut oil temperature. The

 

display shows “7. OIL TMP (temp.)”.

 

Press

to continue onto the CPU TMP reading.

 

8. CPU TMP

 

 

This step shows the present PC board temperature.

 

Press

to continue onto the ANALOG reading.

 

9. ANALOG <1> 2.86V

 

 

This step displays the present status of any channel of the

 

controller’s a to d converter. This feature may be useful to a

 

technician troubleshooting a problem with the fryer or

 

controller.

 

 

The displayed value can be toggled between volts and bits

 

by pressing . If the displayed value has a decimal point,

 

it is voltage (0 to 5 VDC). If no decimal point is shown, the

 

value is a-to-d bits (0 - 4095).

 

 

Press and hold

to exit Information Mode at any

 

 

time, or after 2 minutes, controls automatically exit

 

 

back to normal operation.

403

 

 

3-40

Image 40
Contents Operation Operating Components LID Operation Indicators SwitchesDescription Function Switches and Indicators Description Function Model OFE 403 Clock SET Clock SET Filling or Adding Shortening Product Racking Recommendations Above the Upper Frypot Levelindicator Basic OperationBe Certain the Shortening is Never LINE. Failure to Follow These InstrucAllow fryer to heat until Illuminates Unlatch and raise the lid cautiously Care Shortening Shortening Overflowingthe FrypotWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR PropertyFiltering Instructions Filtering Instructions Rinse Hose When the Main Power Switch Filtering InstructionsOnly Connectand Disconnect the Filter Is in the OFF POSITION. ALSO, USE a DRYEnvelope Filter Pump Motor PROTECTOR-MANUAL Reset Cleaningthe Frypot If hot shortening is present in the frypot, it must be Drained by slowly pulling the drain handle out towards youCleaning the Frypot Does not boil over causing damage to controlsProcedure Frequency Cleaning Nylatrons MonthlyMaintenance PreventiveProgramming Change Product NamesProgramming Programming Filter Cycle Mode OptionalGo to Idle after Done? Global Erase a Prod Preset a Prod Erase ALL Special Program ModeLanguage SP-2 Mode Audio Volume SP-4System Initialization SP-3 Audio Tone SP-5Idle Mode SP-7 Type of shortening to be melted Liquid or Solid SP-6Mixed Press SP-8C shows in the display, if YES Special Program Schedule To filter the shortening. Press To changeClean-Out Temperature Sp-10 Product Buttons Sp-9 ModeClean-Out Temperature Sp-11 Mode Program Code Change SP-15 Usage Code Change SP-16Mode Shows in display If not satisfied with code, press Data LOGGING, Heat CONTROL, Tech MODE, and Stat ModeIf satisfied with code, press Code ChangePress to continue to Last Load Information Mode Last Load Function DisplayexInformation Mode Function Display EXOutp H* P CPU TMP OIL TMPAnalog 1