Toshiba Basic VF-S11 operations, Status monitor mode Mode for monitoring all inverter status

Page 28

E6581160

4. Basic VF-S11 operations

The VF-S11 has the following four monitor modes.

Standard monitor mode : The standard inverter mode. This mode is enabled when inverter power goes on.

This mode is for monitoring the output frequency and setting the frequency designated value. In it is also displayed information about status alarms during running and trips.

•Setting frequency designated values ⇒ see 3.1.2

• Status alarm		4
If there is an error in the inverter, the alarm signal and the frequency will flash		4
alternately in the LED display.
E:	When a current flows at or higher than the overcurrent stall level.
R:	When a voltage is generated at or higher than the over voltage stall
	level.
N:	When a load reaches 50% or higher of the overload trip value.
J:	When the temperature reaches the overheating protection alarm level.

Setting monitor mode : The mode for setting inverter parameters.

		How to set parameters ⇒ see 4.2
Status monitor mode	: The mode for monitoring all inverter status.
	Allows monitoring of set frequencies, output current/voltage and terminal
	information.
		For more on how to use the monitor ⇒ see 5.1
Pressing the key MODE will move the inverter through each of the modes.
		Standard monitor
	MODE	mode	MODE
	MODE
Status monitor			Setting monitor
	mode		mode

		MODE
	Panel jog mode	: This mode allows you to jog the motor by controlling the
	Panel jog mode	operation from the operation panel.
		operation from the operation panel.

This mode is hidden by default.

To use the panel jog mode, set the parameter H to.

27

Image 28

Contents For 3-phase induction motors Industrial InverterSafety precautions Meanings of symbolsSafety precautions Explanation of markingsGeneral Operation Transportation & installation WiringOperations When retry function is selected inverter Maintenance and inspection Contents  Read first Check product purchaseCD-ROM E6581167 Contents of the product InstallationStandard connection diagram ConnectionStandard connections VF-S11FLC FLBFLA PLC OUTPower circuit terminals Selection of wiring materialsPower circuit Description of terminalsControl circuit terminals Control circuit terminals SW124VDC PLC VIAPTC FLB FLARY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Operations Simplified Operation of the VF-S11Eoqf HoqfHow to start and stop Start and stop using the operation panel keys EOQF=Coast stop HOQF= How to set the frequencyExample of operating a run from the panel Setting the frequency using the operation panel HOQF= or Frequency settingHow to operate the VF-S11 Running and stopping using the operation panelEx.2 Running and stopping using external signals Ex.3VIA Panel jog mode Status monitor mode Mode for monitoring all inverter statusBasic VF-S11 operations Standard monitor mode Flow of status monitor modePast trip record detained monitor mode How to set parameters Parameters for detailed and special setting. SeeWhen you adjust the inverter repeatedly using Same parameter. Parameter name CWJ. See How to set the basic parameters⇔HJ How to set extended parameters～H Example of parameter setting Search and resetting of changed parameters I4WHow to search and reprogram parameters ⇔ CEE Parameters that cannot be changed while running How to use the history function⇔CEE How to save/load the user setting parameters Returning all parameters to standard default settingKpkv Monitoring the operation status Status monitor modeStatus monitor under normal conditions Iiii Pgtt ⇔ Display of detailed information on a past trip Display of trip information Trip code displayDisplay of trip information at the occurrence of a trip Example of call-up of trip informationOFF VIA VIB RES QR ⇔Cumulative E6581160 Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 500V class Example of wiring About the low-voltage directiveCompliance with Installation Compliance with UL Standard and CSA StandardMeasures to satisfy the low-voltage directive Compliance with ConnectionAIC, Fuse and Wire sizes Motor thermal protectionAIC a AWGTable of parameters and data User parametersBasic parameters Four navigation functionsCEE QNO Extended parameters Input/output parametersFrequency parameters Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parametersCommunication parameters PM motor parameters Default settings by inverter rating XD／H Table of input terminal functions AD2+SS3+AD2 , H, H, HTable of output terminal functions AD3On QE-,QR-,QJ, ,QJ,WR,GH,WE,QN-,QNT Fcvibn Models and their standard specifications SpecificationsStandard specifications Common specification CharacteristicsSpecification Outside dimensions and mass Outside dimensions and massOutline drawing VF-S11Fig.D Before making a service call Trip information and remedies Trip causes/warnings and remediesQNT Industrial and Power Systems & Services Company