Toshiba VF-S11 manual Three-phase 500V class

Page 47

 

 

 

 

 

 

E6581160

 

 

 

Three-phase 500V class

 

 

 

 

 

 

Combination of inverter and filter

 

 

 

 

Inverter

Transmission noise

Transmission noise

Transmission noise

 

 

 

 

EN55011 Class A Group 1

EN55011 Class B Group 1

EN55011 Class A Group 1

 

 

 

 

Applicable filters

Applicable filters

Applicable filters

 

 

 

 

(Length of motor connecting cable:

(Length of motor connecting cable:

(Length of motor connecting cable:

 

 

 

 

Max. 5 m)

Max. 20 m)

Max. 50 m)

 

 

 

VFS11-4004PL

With a built-in filter

EMFS11

-4015BZ

 

 

 

VFS11-4007PL

With a built-in filter

EMFS11-4015BZ

 

 

 

VFS11-4015PL

With a built-in filter

EMFS11-4015BZ

 

 

 

VFS11-4022PL

With a built-in filter

EMFS11-4025CZ

 

 

 

VFS11-4037PL

With a built-in filter

EMFS11-4025CZ

 

 

 

VFS11-4055PL

With a built-in filter

EMFS11-4047DZ

 

 

 

VFS11-4075PL

With a built-in filter

EMFS11-4047DZ

 

 

 

VFS11-4110PL

With a built-in filter

EMFS11-4049EZ

 

 

 

VFS11-4150PL

With a built-in filter

EMFS11-4049EZ

 

 

 

Single-phase 240V class

 

 

 

 

 

 

Combination of inverter and filter

 

 

 

 

Inverter

Transmission noise

Transmission noise

Transmission noise

 

 

 

 

EN55011 Class A Group 1

EN55011 Class B Group 1

EN55011 Class A Group 1

 

 

 

 

Applicable filters

Applicable filters

Applicable filters

 

 

 

 

(Length of motor connecting cable:

(Length of motor connecting cable:

(Length of motor connecting cable:

6

 

 

 

Max. 5 m)

Max. 20 m)

Max. 50 m)

 

 

VFS11S-2002PL

With a built-in filter

EMFS11S

-2009AZ

 

 

VFS11S-2004PL

With a built-in filter

EMFS11S-2009AZ

 

 

 

VFS11S-2007PL

With a built-in filter

EMFS11S-2009AZ

 

 

 

VFS11S-2015PL

With a built-in filter

EMFS11S-2016BZ

 

 

 

VFS11S-2022PL

With a built-in filter

EMFS11S-2022CZ

Note : For 600V models compliant with EU standards, contact your nearest Toshiba inverter distributor.

(2)Use shielded power cables, such as inverter output cables, and shielded control cables. Route the cables and wires so as to minimize their lengths. Keep a distance between the power cable and the control cable and between the input and output wires of the power cable. Do not route them in parallel or bind them together, instead cross at right angle.

(3)Install the inverter and the filter on the same metal plate. It is more effective in limiting the radiation noise to install the inverter in a sealed steel cabinet. Using wires as thick and short as possible, earth the metal plate and the control panel securely with a distance kept between the earth cable and the power cable.

(4)Route the EMI filter input and output wires apart from each other.

(5)To suppress radiation noise from cables, ground all shielded cables through a noise cut plate.

It is effective to earth shielded cables in the vicinity of the inverter, cabinet and filter (within a radius of 10cm from each of them). Inserting a ferrite core in a shielded cable is even more effective in limiting the radiation noise.

(6)To further limit the radiation noise, insert a zero-phase reactor in the inverter output line and insert ferrite cores in the earth cables of the metal plate and cabinet.

46

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Industrial Inverter For 3-phase induction motorsExplanation of markings Safety precautionsMeanings of symbols Safety precautionsGeneral Operation Wiring Transportation & installationOperations Maintenance and inspection When retry function is selected inverter Contents  Check product purchase Read firstCD-ROM E6581167 Installation Contents of the productVF-S11 Standard connection diagramConnection Standard connectionsPLC OUT FLCFLB FLADescription of terminals Power circuit terminalsSelection of wiring materials Power circuitControl circuit terminals VIA Control circuit terminalsSW1 24VDC PLCFLB FLA PTCRY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Hoqf OperationsSimplified Operation of the VF-S11 Eoqf How to start and stopStart and stop using the operation panel keys EOQF= Coast stopExample of operating a run from the panel How to set the frequencyHOQF= Frequency setting Setting the frequency using the operation panel HOQF= or Running and stopping using the operation panel How to operate the VF-S11Ex.2 Ex.3 Running and stopping using external signalsVIA Basic VF-S11 operations Status monitor mode Mode for monitoring all inverter statusPanel jog mode Past trip record detained monitor mode Flow of status monitor modeStandard monitor mode Same parameter. Parameter name CWJ. See How to set parametersParameters for detailed and special setting. See When you adjust the inverter repeatedly using⇔HJ How to set the basic parameters ～H How to set extended parameters How to search and reprogram parameters Search and resetting of changed parameters I4WExample of parameter setting  ⇔ CEE  ⇔CEE How to use the history functionParameters that cannot be changed while running Kpkv Returning all parameters to standard default settingHow to save/load the user setting parameters Status monitor under normal conditions Status monitor modeMonitoring the operation status Iiii  Pgtt ⇔Display of detailed information on a past trip Example of call-up of trip information Display of trip informationTrip code display Display of trip information at the occurrence of a tripQR ⇔ OFF VIA VIB RESCumulative E6581160 About the EMC directive How to cope with the CE directiveMeasures to satisfy the standards Measures to satisfy the EMC directive Three-phase 500V class About the low-voltage directive Example of wiringCompliance with Connection Compliance with InstallationCompliance with UL Standard and CSA Standard Measures to satisfy the low-voltage directiveAWG AIC, Fuse and Wire sizesMotor thermal protection AIC aFour navigation functions Table of parameters and dataUser parameters Basic parametersCEE  QNOInput/output parameters Extended parametersFrequency parameters   Operation mode parameters   Torque boost parameters Protection parameters Acceleration/deceleration time parameters  Operation panel parameters Output parametersCommunication parameters PM motor parameters XD／H        Default settings by inverter ratingAD2 Table of input terminal functions, H, H, H +SS3+AD2AD3 Table of output terminal functionsQN-,QNT ,QJ,WR,GH,WE,On QE-,QR-,QJ, Fcvibn Standard specifications SpecificationsModels and their standard specifications Characteristics Common specificationSpecification Outside dimensions and mass Outside dimensions and massVF-S11 Outline drawingFig.D Trip causes/warnings and remedies Before making a service call Trip information and remediesQNT   Industrial and Power Systems & Services Company
Top Page Image Contents