Toshiba VF-S11 manual Connection, Standard connections, Standard connection diagram

Page 11

Protective function FLB activation output

Low-speed

signal output RC 24Vdc input PLC

FLA

FLC

Meter

FM

+

RY

R/L1

S/L2

T/L3

*1

E6581160

2. Connection

2.1 Standard connections

2

2.1.1 Standard connection diagram 1

This diagram shows a standard wiring of the main circuit.

Standard connection diagram - SINK (Negative) (common:CC)

DC reactor (DCL) *2 (option)

Braking resistor (option)

P0 PA/+ PB PC/-

Main circuit power supply	MCCB
240V class: three-phase 200-240V

-50/60Hz

500V class: three-phase 380-500V -50/60Hz

600V class: three-phase 525-600V

		-50/60Hz
		MCCB(2P)
Power supply		R/L1
1	200~240V
-50/60Hz		S/L2
		S/L2

				U/T1	Motor
				U/T1
Noise	Power circuit			V/T2	I M
filter *5	Power circuit			W/T3	I M
filter *5				W/T3
	Control		F		Forward
	circuit		R		Reverse
			R		Reverse
	VF-S11	RES			Reset
	VF-S11
	Operation panel S1				Preset-speed 1
	Connector for		S2		Preset-speed 2
	common serial		S3		Preset-speed 3
	communications

*1: The T/L3 terminal is not provided for single-phase models.

Use the R/L1 and S/L2 terminal as input terminals.

*2: The inverter is supplied with the PO

	SW1	FM	VIA	CC	Common
	SOURCE	V	V

PLC	P24		Speed reach
	OUT	Ry	signal output

and the PA/+ terminals shorted by means of a shorting bar.

Before installing the DC reactor (DCL), remove the bar.

*3: When using the OUT output terminal in sink logic mode, short the NO and CC terminals.

*4: If you are using a 600V model, be sure to connect an input reactor (ACL).

*5: 600V models have no noise filter inside.

Frequency meter (ammeter)

-

7.5V-1mA (or 4-20mA)

SINK	I	I NO		*3
			CC	*3
CC VIA	VIB	PP	CC
CC VIA	VIB	PP
			+	Voltage signal: 0-10V
			-	Voltage signal: 0-10V
			-	(Current signal: 4-20mA)
				(Current signal: 4-20mA)

External potentiometer (1~10kΩ)

(or input voltage signal across VIB-CC terminals: 0-10V)

10

Image 11

Contents Industrial Inverter For 3-phase induction motorsExplanation of markings Safety precautionsMeanings of symbols Safety precautionsGeneral Operation Wiring Transportation & installationOperations Maintenance and inspection When retry function is selected inverter Contents  Check product purchase Read firstCD-ROM E6581167 Installation Contents of the productVF-S11 Standard connection diagramConnection Standard connectionsPLC OUT FLCFLB FLADescription of terminals Power circuit terminalsSelection of wiring materials Power circuitControl circuit terminals VIA Control circuit terminalsSW1 24VDC PLCFLB FLA PTCRY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Hoqf OperationsSimplified Operation of the VF-S11 Eoqf How to start and stopStart and stop using the operation panel keys EOQF= Coast stopExample of operating a run from the panel How to set the frequencyHOQF= Frequency setting Setting the frequency using the operation panel HOQF= or Running and stopping using the operation panel How to operate the VF-S11Ex.2 Ex.3 Running and stopping using external signalsVIA Basic VF-S11 operations Status monitor mode Mode for monitoring all inverter statusPanel jog mode Past trip record detained monitor mode Flow of status monitor modeStandard monitor mode Same parameter. Parameter name CWJ. See How to set parametersParameters for detailed and special setting. See When you adjust the inverter repeatedly using⇔HJ How to set the basic parameters ～H How to set extended parameters How to search and reprogram parameters Search and resetting of changed parameters I4WExample of parameter setting ⇔ CEE ⇔CEE How to use the history functionParameters that cannot be changed while running Kpkv Returning all parameters to standard default settingHow to save/load the user setting parameters Status monitor under normal conditions Status monitor modeMonitoring the operation status Iiii Pgtt ⇔Display of detailed information on a past trip Example of call-up of trip information Display of trip informationTrip code display Display of trip information at the occurrence of a tripQR ⇔ OFF VIA VIB RESCumulative E6581160 About the EMC directive How to cope with the CE directiveMeasures to satisfy the standards Measures to satisfy the EMC directive Three-phase 500V class About the low-voltage directive Example of wiringCompliance with Connection Compliance with InstallationCompliance with UL Standard and CSA Standard Measures to satisfy the low-voltage directiveAWG AIC, Fuse and Wire sizesMotor thermal protection AIC aFour navigation functions Table of parameters and dataUser parameters Basic parametersCEE QNOInput/output parameters Extended parametersFrequency parameters Operation mode parameters Torque boost parameters Protection parameters Acceleration/deceleration time parameters Operation panel parameters Output parametersCommunication parameters PM motor parameters XD／H Default settings by inverter ratingAD2 Table of input terminal functions, H, H, H +SS3+AD2AD3 Table of output terminal functionsQN-,QNT ,QJ,WR,GH,WE,On QE-,QR-,QJ, Fcvibn Standard specifications SpecificationsModels and their standard specifications Characteristics Common specificationSpecification Outside dimensions and mass Outside dimensions and massVF-S11 Outline drawingFig.D Trip causes/warnings and remedies Before making a service call Trip information and remediesQNT Industrial and Power Systems & Services Company