Toshiba VF-S11 manual ,Qj,Wr,Gh,We,, On QE-,QR-,QJ,, Qn-,Qnt

E6581160

QTable of output terminal functions 2

	Function	Code	Function	Action
	No.
	12	OT	Over-torque detection	ON: Torque current is equal to or larger than
				H set value and longer than H
				set time.
				OFF: The torque current is equal to or less than
				(H set value - H set value).
	13	OTN	Inversion of over-torque detection	Inversion of OT
	14	RUN	Start/Stop	ON: When operation frequency is output or during
				(FD)
				OFF: Operation stopped
	15	RUNN	Inversion of RUN/STOP	Inversion of RUN setting
	16	POL	OL pre-alarm	ON: 50% or more of calculated value of overload
				protection level
				OFF: Less than 50% of calculated value of
				overload protection level
	17	POLN	Inversion of OL pre-alarm	Inversion of POL setting
	18	POHR	Braking resistor overload pre-alarm	ON: 50% or more of calculated value of H
				set overload protection level
				OFF: Less than 50% of calculated value of
				H set overload protection level
	19	POHRN	Inversion of braking resistor overload pre-alarm	Inversion of RCHR setting
	20	POT	Over-torque detection pre-alarm	ON: Torque current is equal to or larger than 70%
				of H set value.
				OFF: The torque current is below (H set
				value x 70% - H set value).
	21	POTN	Inversion of over-torque detection pre-alarm	Inversion of POT setting
7
	22	PAL	Pre-alarm	One of the following is turned on:
				ON POL, POHR, POT, MOFF, UC, OT, LL
				stop, COT, and momentary power failure
				slowdown stop.
				or E,R,QTJ issues an alarm
				All the following are turned off:
				OFF POL, POHR, POT, MOFF, UC, OT, LL
				stop, COT, and momentary power failure
				slowdown stop.
				or E,R,QTJ issues no alarm
	23	PALN	Inversion of pre-alarm	Inversion of PAL setting
	24	UC	Small-current detection	ON: The output current is equal to or less than
				H set value for H set time.
				OFF: The output current is equal to or larger than
				H set value + 10%.
	25	UCN	Inversion of small-current detection	Inversion of UC setting
	26	HFL	Significant failure	ON: QEC,QEN,QV,G,
				GGR,GVP,GRJQ,GTT-
				,QJ,WR,GH,WE,
				GV[R,QTGRJ)
				OFF: Failure other than the above
	27	HFLN	Inversion of significant failure	Inversion of HFL setting
	28	LFL	Insignificant failure	ON: (QE-,QR-,QJ,
				QN-,QNT)
				OFF: Failure other than the above
	29	LFLN	Inversion of insignificant failure	Inversion of LFL setting
	30	RDY1	Ready for operation (including ST/RUN)	ON: Ready for operation (ST and RUN are also
				ON)
				OFF: Others
	31	RDY1N	Inversion of ready for operation (including	Inversion of RDY1 setting
			ST/RUN)
	32	RDY2	Ready for operation (excluding ST/RUN)	ON: Ready for operation (ST and RUN are not
				ON)
				OFF: Others
	33	RDY2N	Inversion of ready for operation (excluding ST/RUN)	Inversion of RDY2
	34	FCVIB	Frequency VIB selection	ON: VIB selected as frequency command
				OFF: Terminal other than VIB selected as
				frequency command

68