Toshiba VF-S11 manual Operations

Page 5

I

E6581160

Danger

•Electrical installation work must be done by a qualified expert.

Connection of input power by someone who does not have that expert knowledge may result in fire or electric shock.

•Connect output terminals (motor side) correctly.

If the phase sequence is incorrect, the motor will operate in reverse and that may result in injury.

•Wiring must be done after installation.

If wiring is done prior to installation that may result in injury or electric shock

•The following steps must be performed before wiring.

(1) Turn off all input power.

Mandatory

(2)

Wait at least ten minutes and check to make sure that the charge lamp is no longer lit.

(3)

Use a tester that can measure DC voltage (800VDC or more), and check to make sure that the

 

 

 

voltage to the DC main circuits (across PA-PC) is 45V or less.

 

If these steps are not properly performed, the wiring will cause electric shock.

•Tighten the screws on the terminal board to specified torque.

If the screws are not tightened to the specified torque, it may lead to fire.

•Check to make sure that the input power voltage is +10%, -15% of the rated power voltage written on the rating label (±10% when the load is 100% in continuous operation).

If the input power voltage is not +10%, -15% of the rated power voltage (±10% when the load is 100% in continuous operation) this may result in fire.

•Ground must be connected securely.

If the ground is not securely connected, it could lead to electric shock or fire when a malfunction or current leak occurs.

Be Grounded

Warning

•Do not attach equipment (such as noise filters or surge absorbers) that have built-in capacitors to the output (motor side) terminals.

That could result in a fire.

Prohibited

QOperations

Danger

 

 

 

• Do not touch inverter terminals when electrical power is going to the inverter even if the motor is

 

 

 

 

stopped.

 

 

 

 

Touching the inverter terminals while power is connected to it may result in electric shock.

 

 

 

 

 

 

 

• Do not touch switches when the hands are wet and do not try to clean the inverter with a damp cloth.

 

 

 

 

Such practices may result in electric shock.

Prohibited

 

•

Do not go near the motor in alarm-stop status when the retry function is selected.

 

 

 

 

The motor may suddenly restart and that could result in injury.

 

 

 

 

Take measures for safety, e.g. attaching a cover to the motor, against accidents when the motor

 

 

 

 

unexpectedly restarts.

 

 

 

• Turn input power on after attaching the front cover.

 

 

 

 

When installed inside a cabinet and using with the front cover removed, always close the cabinet doors

 

 

 

 

 

 

 

 

first and then turn power on. If the power is turned on with the front cover or the cabinet doors open, it

 

 

 

 

may result in electric shock.

Mandatory

 

•

Make sure that operation signals are off before resetting the inverter after malfunction.

 

 

 

 

If the inverter is reset before turning off the operating signal, the motor may restart suddenly causing

 

 

 

 

injury.

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Industrial Inverter For 3-phase induction motorsMeanings of symbols Safety precautionsSafety precautions Explanation of markingsGeneral Operation Wiring Transportation & installationOperations Maintenance and inspection When retry function is selected inverter Contents  Check product purchase Read firstCD-ROM E6581167 Installation Contents of the productConnection Standard connection diagramStandard connections VF-S11FLB FLCFLA PLC OUTSelection of wiring materials Power circuit terminalsPower circuit Description of terminalsControl circuit terminals SW1 Control circuit terminals24VDC PLC VIAFLB FLA PTCRY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Simplified Operation of the VF-S11 OperationsEoqf HoqfStart and stop using the operation panel keys EOQF= How to start and stopCoast stop Example of operating a run from the panel How to set the frequencyHOQF= Frequency setting Setting the frequency using the operation panel HOQF= or Running and stopping using the operation panel How to operate the VF-S11Ex.2 Ex.3 Running and stopping using external signalsVIA Basic VF-S11 operations Status monitor mode Mode for monitoring all inverter statusPanel jog mode Past trip record detained monitor mode Flow of status monitor modeStandard monitor mode Parameters for detailed and special setting. See How to set parametersWhen you adjust the inverter repeatedly using Same parameter. Parameter name CWJ. See⇔HJ How to set the basic parameters ～H How to set extended parameters How to search and reprogram parameters Search and resetting of changed parameters I4WExample of parameter setting  ⇔ CEE  ⇔CEE How to use the history functionParameters that cannot be changed while running Kpkv Returning all parameters to standard default settingHow to save/load the user setting parameters Status monitor under normal conditions Status monitor modeMonitoring the operation status Iiii  Pgtt ⇔Display of detailed information on a past trip Trip code display Display of trip informationDisplay of trip information at the occurrence of a trip Example of call-up of trip informationQR ⇔ OFF VIA VIB RESCumulative E6581160 About the EMC directive How to cope with the CE directiveMeasures to satisfy the standards Measures to satisfy the EMC directive Three-phase 500V class About the low-voltage directive Example of wiringCompliance with UL Standard and CSA Standard Compliance with InstallationMeasures to satisfy the low-voltage directive Compliance with ConnectionMotor thermal protection AIC, Fuse and Wire sizesAIC a AWGUser parameters Table of parameters and dataBasic parameters Four navigation functionsCEE  QNOInput/output parameters Extended parametersFrequency parameters   Operation mode parameters   Torque boost parameters Protection parameters Acceleration/deceleration time parameters  Operation panel parameters Output parametersCommunication parameters PM motor parameters XD／H        Default settings by inverter ratingAD2 Table of input terminal functions, H, H, H +SS3+AD2AD3 Table of output terminal functionsQN-,QNT ,QJ,WR,GH,WE,On QE-,QR-,QJ, Fcvibn Standard specifications SpecificationsModels and their standard specifications Characteristics Common specificationSpecification Outside dimensions and mass Outside dimensions and massVF-S11 Outline drawingFig.D Trip causes/warnings and remedies Before making a service call Trip information and remediesQNT   Industrial and Power Systems & Services Company
Top Page Image Contents