Toshiba VF-S11 manual How to set the basic parameters, , ⇔Hj

Page 31

E6581160

4.2.1How to set the basic parameters

All of the basic parameters can be set by the same step procedures.

[Steps in key entry for basic parameters]

MODE Switches to the setting monitor mode.

Selects parameter to be changed.

4

Reads the programmed parameter setting.

Changes the parameter setting.

Saves the changed value of the parameter setting.

*Parameters were factory-set by default before shipment.

*Select the parameter to be changed from "Table of parameters".

*If there is something that you do not understand during the operation, press the MODE key to return to the indication.

*See 7.2 for basic parameters.

Steps in setting are as follows (example of changing the maximum frequency from 80Hz to 60Hz).

Key operated

LED display

Operation

Displays the operation frequency (operation stopped).

(When standard monitor display selection H= [Operation

frequency])

MODE

CWJ

The first basic parameter “CWJ” (history function) is displayed.

HJ

Press either the

or

key to select “HJ”.

Pressing the ENTER key reads the maximum frequency.

Press the

key to change the maximum frequency to 60Hz.

⇔HJ

Press the ENT key to save the maximum frequency. HJ and the

frequency are displayed alternately.

After this,

→Displays the same

→Switches to the

→Displays names

MODE

programmed

display in the

of other

parameter.

status monitor

parameters.

mode.

30

Image 31

Contents Industrial Inverter For 3-phase induction motorsExplanation of markings Safety precautionsMeanings of symbols Safety precautionsGeneral Operation Wiring Transportation & installationOperations Maintenance and inspection When retry function is selected inverter Contents  Check product purchase Read firstCD-ROM E6581167 Installation Contents of the productVF-S11 Standard connection diagramConnection Standard connectionsPLC OUT FLCFLB FLADescription of terminals Power circuit terminalsSelection of wiring materials Power circuitControl circuit terminals VIA Control circuit terminalsSW1 24VDC PLCFLB FLA PTCRY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Hoqf OperationsSimplified Operation of the VF-S11 Eoqf How to start and stopStart and stop using the operation panel keys EOQF= Coast stopHOQF= How to set the frequencyExample of operating a run from the panel Frequency setting Setting the frequency using the operation panel HOQF= or Running and stopping using the operation panel How to operate the VF-S11Ex.2 Ex.3 Running and stopping using external signalsVIA Panel jog mode Status monitor mode Mode for monitoring all inverter statusBasic VF-S11 operations Standard monitor mode Flow of status monitor modePast trip record detained monitor mode Same parameter. Parameter name CWJ. See How to set parametersParameters for detailed and special setting. See When you adjust the inverter repeatedly using How to set the basic parameters⇔HJ How to set extended parameters～H Example of parameter setting Search and resetting of changed parameters I4WHow to search and reprogram parameters ⇔ CEE Parameters that cannot be changed while running How to use the history function⇔CEE How to save/load the user setting parameters Returning all parameters to standard default settingKpkv Monitoring the operation status Status monitor modeStatus monitor under normal conditions Iiii Pgtt ⇔Display of detailed information on a past trip Example of call-up of trip information Display of trip informationTrip code display Display of trip information at the occurrence of a tripQR ⇔ OFF VIA VIB RESCumulative E6581160 Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 500V class About the low-voltage directive Example of wiringCompliance with Connection Compliance with InstallationCompliance with UL Standard and CSA Standard Measures to satisfy the low-voltage directiveAWG AIC, Fuse and Wire sizesMotor thermal protection AIC aFour navigation functions Table of parameters and dataUser parameters Basic parametersCEE QNOInput/output parameters Extended parametersFrequency parameters Operation mode parameters Torque boost parameters Protection parameters Acceleration/deceleration time parameters Operation panel parameters Output parametersCommunication parameters PM motor parameters XD／H Default settings by inverter ratingAD2 Table of input terminal functions, H, H, H +SS3+AD2AD3 Table of output terminal functionsOn QE-,QR-,QJ, ,QJ,WR,GH,WE,QN-,QNT Fcvibn Models and their standard specifications SpecificationsStandard specifications Characteristics Common specificationSpecification Outside dimensions and mass Outside dimensions and massVF-S11 Outline drawingFig.D Trip causes/warnings and remedies Before making a service call Trip information and remediesQNT Industrial and Power Systems & Services Company