Toshiba VF-S11 manual How to set extended parameters, , ～H

Page 32

E6581160

4.2.2How to set extended parameters

The VF-S11 has extended parameters to allow you to make full use of its functions.

All extended parameters are expressed with H and three digits.

Basic parameters

H

ENT

MODE

H～H

4

Press the MODE key once and use the VW key to select H from the basic parameters.

[Steps in key entry for extended parameters]

Press the V key or the W key to change the set value. Pressing the ENTER key allows the reading of parameter setting.

		: switches to the setting monitor mode.(Displays CWJ)
MODE		: switches to the setting monitor mode.(Displays CWJ)	* See 7.3 for extended
			parameters.

:Selects "H" from basic parameters.

:The first extended parameter “HK” (Low-speed signal output frequency) is displayed.

:Selects the extended parameter whose setting needs to be changed.

:Reads the programmed parameter setting.

: Changes the parameter setting.

Saves the changed value of the extended parameter setting.

Pressing the MODE key instead of the key moves back to the previous status.

31

Image 32

Contents For 3-phase induction motors Industrial InverterSafety precautions Meanings of symbolsSafety precautions Explanation of markingsGeneral Operation Transportation & installation WiringOperations When retry function is selected inverter Maintenance and inspection Contents  Read first Check product purchaseCD-ROM E6581167 Contents of the product InstallationStandard connection diagram ConnectionStandard connections VF-S11FLC FLBFLA PLC OUTPower circuit terminals Selection of wiring materialsPower circuit Description of terminalsControl circuit terminals Control circuit terminals SW124VDC PLC VIAPTC FLB FLARY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Operations Simplified Operation of the VF-S11Eoqf HoqfHow to start and stop Start and stop using the operation panel keys EOQF=Coast stop Example of operating a run from the panel How to set the frequencyHOQF= Setting the frequency using the operation panel HOQF= or Frequency settingHow to operate the VF-S11 Running and stopping using the operation panelEx.2 Running and stopping using external signals Ex.3VIA Basic VF-S11 operations Status monitor mode Mode for monitoring all inverter statusPanel jog mode Past trip record detained monitor mode Flow of status monitor modeStandard monitor mode How to set parameters Parameters for detailed and special setting. SeeWhen you adjust the inverter repeatedly using Same parameter. Parameter name CWJ. See⇔HJ How to set the basic parameters ～H How to set extended parameters How to search and reprogram parameters Search and resetting of changed parameters I4WExample of parameter setting ⇔ CEE ⇔CEE How to use the history functionParameters that cannot be changed while running Kpkv Returning all parameters to standard default settingHow to save/load the user setting parameters Status monitor under normal conditions Status monitor modeMonitoring the operation status Iiii Pgtt ⇔ Display of detailed information on a past trip Display of trip information Trip code displayDisplay of trip information at the occurrence of a trip Example of call-up of trip informationOFF VIA VIB RES QR ⇔Cumulative E6581160 About the EMC directive How to cope with the CE directiveMeasures to satisfy the standards Measures to satisfy the EMC directive Three-phase 500V class Example of wiring About the low-voltage directiveCompliance with Installation Compliance with UL Standard and CSA StandardMeasures to satisfy the low-voltage directive Compliance with ConnectionAIC, Fuse and Wire sizes Motor thermal protectionAIC a AWGTable of parameters and data User parametersBasic parameters Four navigation functionsCEE QNO Extended parameters Input/output parametersFrequency parameters Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parametersCommunication parameters PM motor parameters Default settings by inverter rating XD／H Table of input terminal functions AD2+SS3+AD2 , H, H, HTable of output terminal functions AD3QN-,QNT ,QJ,WR,GH,WE,On QE-,QR-,QJ, Fcvibn Standard specifications SpecificationsModels and their standard specifications Common specification CharacteristicsSpecification Outside dimensions and mass Outside dimensions and massOutline drawing VF-S11Fig.D Before making a service call Trip information and remedies Trip causes/warnings and remediesQNT Industrial and Power Systems & Services Company