Toshiba VF-S11 manual Fcvibn

Page 70

E6581160

QTable of output terminal functions 3

	Function	Code	Function	Action
	No.	Code	Function	Action
	No.
	35	FCVIBN	Inversion of frequency VIB selection	Inversion of FCVIB
	36	FLR	Fault signal (put out also at the time of a retry)	ON: When inverter trips or retries
				OFF: When inverter does not trip or retry
	37	FLRN	Inversion of failure signal (put out also at the time	Inversion of FLR
			of a retry)
	38	OUT0	Specified data output 1	ON: Specified data from remote control FA50:
				BIT0= 1
				OFF: Specified data from remote control FA50:
				BIT0= 0
	39	OUT0N	Inversion of specified data output 1	Inversion of OUT0 setting
	40	OUT1	Specified data output 2	ON: Specified data from remote control FA50:
				BIT1= 1
				OFF: Specified data from remote control FA50:
				BIT1= 0
	41	OUT1N	Inversion of specified data output 2	Inversion of OUT1 setting
	42	COT	Cumulative operation time alarm	ON: Cumulative operation time is equal to or
				longer than H
				OFF: Cumulative operation time is shorter than
				H
	43	COTN	Inversion of cumulative operation time alarm	Inversion of COT
	44	LTA	Parts replacement alarm	ON: Calculation for parts replacement time is
				equal to or longer than the preset time
				ON: Calculation for parts replancement time is
				shorter than the preset time
	45	LTAN	Inversion of replacement alarm	Inversion of LTA
	45	LTAN	Inversion of replacement alarm	Inversion of LTA		7
	46	BR	Braking sequence output	ON: Braking retention signal
				OFF: Braking release signal
	47	BRN	Inversion of braking sequence output	Inversion of BR

	48	LI1	F terminal input signal	ON: The signal input to F terminal is ON
				OFF: The signal input to F terminal is OFF
	49	LI1N	Inversion of F terminal input signal	Inversion of LI1
	50	LI2	R terminal input signal	ON: The signal input to R terminal is ON
				OFF: The signal input to R terminal is OFF
	51	LI2N	Inversion of R terminal input signal	Inversion of LI2
	52	PIDF	Signal in accordance of frequency command	ON: Frequency commanded by HOQF or
				H and that by VIA show the same
				value.
				OFF: Frequency commanded by HOQF or
				H and that by VIA show different
				values.
	53	PIDFN	Inversion of signal in accordance of frequency	Inversion of PIDF setting
			command
	54	MOFF	Undervoltage detection	ON: Undervoltage detected
				OFF: Other than undervoltage
	55	MOFFN	Inversion of undervoltage detection	Inversion of MOFF
	56-253	Disabled	Invalid settings, always OFF (ignored)	Invalid settings, always OFF (ignored)
	254	AOFF	Always OFF	Always OFF
	255	AON	Always ON	Always ON

69

Image 70

Contents For 3-phase induction motors Industrial InverterSafety precautions Safety precautionsMeanings of symbols Explanation of markingsGeneral Operation Transportation & installation WiringOperations When retry function is selected inverter Maintenance and inspection Contents  Read first Check product purchaseCD-ROM E6581167 Contents of the product InstallationStandard connections Standard connection diagramConnection VF-S11FLA FLCFLB PLC OUTPower circuit Power circuit terminalsSelection of wiring materials Description of terminalsControl circuit terminals 24VDC PLC Control circuit terminalsSW1 VIAPTC FLB FLARY RC Slide switch SW1PLC Source Positive logic SW1 Source PLC Sink Eoqf OperationsSimplified Operation of the VF-S11 HoqfCoast stop How to start and stopStart and stop using the operation panel keys EOQF= HOQF= How to set the frequencyExample of operating a run from the panel Setting the frequency using the operation panel HOQF= or Frequency settingHow to operate the VF-S11 Running and stopping using the operation panelEx.2 Running and stopping using external signals Ex.3VIA Panel jog mode Status monitor mode Mode for monitoring all inverter statusBasic VF-S11 operations Standard monitor mode Flow of status monitor modePast trip record detained monitor mode When you adjust the inverter repeatedly using How to set parametersParameters for detailed and special setting. See Same parameter. Parameter name CWJ. See How to set the basic parameters⇔HJ How to set extended parameters～H Example of parameter setting Search and resetting of changed parameters I4WHow to search and reprogram parameters ⇔ CEE Parameters that cannot be changed while running How to use the history function⇔CEE How to save/load the user setting parameters Returning all parameters to standard default settingKpkv Monitoring the operation status Status monitor modeStatus monitor under normal conditions Iiii Pgtt ⇔ Display of detailed information on a past trip Display of trip information at the occurrence of a trip Display of trip informationTrip code display Example of call-up of trip informationOFF VIA VIB RES QR ⇔Cumulative E6581160 Measures to satisfy the standards How to cope with the CE directiveAbout the EMC directive Measures to satisfy the EMC directive Three-phase 500V class Example of wiring About the low-voltage directiveMeasures to satisfy the low-voltage directive Compliance with InstallationCompliance with UL Standard and CSA Standard Compliance with ConnectionAIC a AIC, Fuse and Wire sizesMotor thermal protection AWGBasic parameters Table of parameters and dataUser parameters Four navigation functionsCEE QNO Extended parameters Input/output parametersFrequency parameters Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Protection parameters Output parameters Operation panel parametersCommunication parameters PM motor parameters Default settings by inverter rating XD／H Table of input terminal functions AD2+SS3+AD2 , H, H, HTable of output terminal functions AD3On QE-,QR-,QJ, ,QJ,WR,GH,WE,QN-,QNT Fcvibn Models and their standard specifications SpecificationsStandard specifications Common specification CharacteristicsSpecification Outside dimensions and mass Outside dimensions and massOutline drawing VF-S11Fig.D Before making a service call Trip information and remedies Trip causes/warnings and remediesQNT Industrial and Power Systems & Services Company